randy
93cbc7b50c
* Updated examples to use the new NewRemodeCode::on, ::off, ::dim and ::on_with_dim notation.
110 lines
3.3 KiB
Arduino
110 lines
3.3 KiB
Arduino
/*
|
|
* This sketch demonstrates how to use InterruptChain to receive and
|
|
* decode remote switches (old and new) and remote sensors.
|
|
*
|
|
* Basically, this sketch combines the features of the ShowReceivedCode
|
|
* and ShowReceivedCodeNewKaku examples of RemoteSwitch and the
|
|
* ThermoHygroReceiver of RemoteSensor all at the same time!
|
|
*
|
|
* After uploading, enable the serial monitor at 115200 baud.
|
|
* When you press buttons on a 433MHz remote control, as supported by
|
|
* RemoteSwitch or NewRemoteSwitch, the code will be echoed.
|
|
* At the same time, if data of a remote thermo/hygro-sensor is
|
|
* received, as supported by RemoteSensor, it will be echoed as well.
|
|
*
|
|
* Setup:
|
|
* - connect a 433MHz receiver on digital pin 2.
|
|
*/
|
|
|
|
#include <RemoteReceiver.h>
|
|
#include <NewRemoteReceiver.h>
|
|
#include <SensorReceiver.h>
|
|
#include <InterruptChain.h>
|
|
|
|
void setup() {
|
|
Serial.begin(115200);
|
|
|
|
// Interrupt -1 to indicate you will call the interrupt handler with InterruptChain
|
|
RemoteReceiver::init(-1, 2, showOldCode);
|
|
|
|
// Again, interrupt -1 to indicate you will call the interrupt handler with InterruptChain
|
|
NewRemoteReceiver::init(-1, 2, showNewCode);
|
|
|
|
// And once more, interrupt -1 to indicate you will call the interrupt handler with InterruptChain
|
|
SensorReceiver::init(-1, showTempHumi);
|
|
|
|
// On interrupt, call the interrupt handlers of remote and sensor receivers
|
|
InterruptChain::addInterruptCallback(0, RemoteReceiver::interruptHandler);
|
|
InterruptChain::addInterruptCallback(0, NewRemoteReceiver::interruptHandler);
|
|
InterruptChain::addInterruptCallback(0, SensorReceiver::interruptHandler);
|
|
}
|
|
|
|
void loop() {
|
|
// You can do other stuff here!
|
|
}
|
|
|
|
// shows the received code sent from an old-style remote switch
|
|
void showOldCode(unsigned long receivedCode, unsigned int period) {
|
|
// Print the received code.
|
|
Serial.print("Code: ");
|
|
Serial.print(receivedCode);
|
|
Serial.print(", period: ");
|
|
Serial.print(period);
|
|
Serial.println("us.");
|
|
}
|
|
|
|
// Shows the received code sent from an new-style remote switch
|
|
void showNewCode(NewRemoteCode receivedCode) {
|
|
// Print the received code.
|
|
Serial.print("Addr ");
|
|
Serial.print(receivedCode.address);
|
|
|
|
if (receivedCode.groupBit) {
|
|
Serial.print(" group");
|
|
} else {
|
|
Serial.print(" unit ");
|
|
Serial.print(receivedCode.unit);
|
|
}
|
|
|
|
switch (receivedCode.switchType) {
|
|
case NewRemoteCode::off:
|
|
Serial.print(" off");
|
|
break;
|
|
case NewRemoteCode::on:
|
|
Serial.print(" on");
|
|
break;
|
|
case NewRemoteCode::dim:
|
|
Serial.print(" dim level ");
|
|
Serial.print(receivedCode.dimLevel);
|
|
break;
|
|
case NewRemoteCode::on_with_dim:
|
|
Serial.print(" on with dim level ");
|
|
Serial.print(receivedCode.dimLevel);
|
|
break;
|
|
}
|
|
|
|
Serial.print(", period: ");
|
|
Serial.print(receivedCode.period);
|
|
Serial.println("us.");
|
|
}
|
|
|
|
// Shows the received sensor data
|
|
void showTempHumi(byte *data) {
|
|
// is data a ThermoHygro-device?
|
|
if ((data[3] & 0x1f) == 0x1e) {
|
|
// Yes!
|
|
byte channel, randomId;
|
|
int temp;
|
|
short int humidity;
|
|
|
|
// Decode the data
|
|
SensorReceiver::decodeThermoHygro(data, channel, randomId, temp, humidity);
|
|
|
|
// Print temperature. Note: temp is 10x the actual temperature!
|
|
Serial.print("Temperature: ");
|
|
Serial.print(temp / 10); // units
|
|
Serial.print('.');
|
|
Serial.println(temp % 10); // decimal
|
|
}
|
|
}
|