mirror of
https://github.com/letscontrolit/ESPEasy.git
synced 2026-09-12 17:45:49 +00:00
96 lines
2.4 KiB
Plaintext
96 lines
2.4 KiB
Plaintext
.. These P001 commands should be moved to core (P000)...
|
|
|
|
:ref:`P000_page` |P000_status|
|
|
|
|
Supported hardware: |P000_usedby_GPIO|
|
|
|
|
.. csv-table::
|
|
:header: "Command (GPIO/Value)", "Extra information"
|
|
:widths: 20, 30
|
|
|
|
"
|
|
``GPIO,<gpio>,<state>``
|
|
|
|
GPIO: 0 ... 16
|
|
|
|
State:
|
|
|
|
**2** (HIGH-Z)
|
|
|
|
**1** (HIGH)
|
|
|
|
**0** (LOW)
|
|
","
|
|
**Basic on/off.**.
|
|
We can control a pin with simple http URL commands. To change the pin to high or low steady output. Setting GPIO to **2** means
|
|
that it will be able to detect low level relays (with high impedance, Z).
|
|
"
|
|
"
|
|
``LongPulse,<GPIO>,<state>,<duration>``
|
|
|
|
GPIO: 0 ... 16
|
|
|
|
State: 1/0
|
|
|
|
Duration: 1 ... 999 S
|
|
","
|
|
**To send a *long* pulse to a certain pin.**.
|
|
A long pulse is basically the same as the plain pulse. The only difference is the time base in seconds rather than in milliseconds.
|
|
So it's more suitable for longer duration.
|
|
"
|
|
"
|
|
``LongPulse_mS,<GPIO>,<state>,<duration>``
|
|
|
|
GPIO: 0 ... 16
|
|
|
|
State: 1/0
|
|
|
|
Duration: 1000 ... 15000 mS
|
|
","
|
|
**To send a *long* pulse to a certain pin.**
|
|
A long pulse (mS) is the same as the regular long pulse. The only difference is the time base in milliseconds rather than in seconds.
|
|
"
|
|
"
|
|
``Pulse,<GPIO>,<state>,<duration>``
|
|
|
|
GPIO: 0 ... 16
|
|
|
|
State: 1/0
|
|
|
|
Duration: 0 ... 1000 mS
|
|
","
|
|
**To send a *short* pulse to a certain pin.**
|
|
Example to send an active high (1) pulse on GPIO 14 for 500 mSeconds. Pulse duration is in milliseconds. State is 1 or 0.
|
|
"
|
|
"
|
|
``PWM,<GPIO>,<state>``
|
|
|
|
``PWM,<GPIO>,<state>,<duration>``
|
|
|
|
GPIO: 0 ... **15**
|
|
|
|
State: 0 ... 1023
|
|
|
|
Duration: 100 ... 15000 mS (optional)
|
|
","
|
|
**To set a certain PWM level.**
|
|
If you have set a certain GPIO to a PWM level and want to use it as a regular HIGH/LOW pin you need to reset by setting the PWM level to 0.
|
|
You can use the duration (ms) parameter to create a fading.
|
|
"
|
|
"
|
|
``Servo,<servo>,<GPIO>,<position>``
|
|
|
|
GPIO: 0 ... **15**
|
|
|
|
Servo: 1/2
|
|
|
|
Position: -180 ... 180 (see warning below)
|
|
","
|
|
**To control a servo motor.**
|
|
We currently support a maximum of two servo motors so you can build a pan & tilt device if you like.
|
|
|
|
.. warning::
|
|
Most servos are not able to turn full 360°! Normally the servos are able to go from **-90°** to **90°**, some rare servos do allow for -135° to 135°.
|
|
|
|
"
|