mirror of
https://github.com/letscontrolit/ESPEasy.git
synced 2026-09-12 09:36:59 +00:00
Gijs Noorlander
bede949bef
The HTML parser does not parse our own rules which is where it is used. So until we have a rules highlighter, we use the ``none`` highlighter.
126 lines
3.6 KiB
ReStructuredText
126 lines
3.6 KiB
ReStructuredText
.. include:: ../Plugin/_plugin_substitutions_p02x.repl
|
|
.. _P028_BME280_page:
|
|
|
|
BME280
|
|
======
|
|
|
|
|P028_typename|
|
|
|P028_status|
|
|
|
|
.. image:: P028_BME280_1.jpg
|
|
|
|
Introduction
|
|
------------
|
|
|
|
Specifications:
|
|
* Temperature (-40C to +85C)
|
|
* Relative humidity (0-100 %RH)
|
|
* Barometric pressure (300-1100 hPa)
|
|
|
|
.. warning:: The BME280 is easily mistaken for its sibling the BM**P**280. Sometimes the PCB have both BME and BMP280
|
|
written on it, it's probably because the footprint is the same for BME and BMP = the same PCB board is used
|
|
by both.
|
|
|
|
Wiring
|
|
------
|
|
|
|
.. code-block:: none
|
|
|
|
ESP BME280
|
|
GPIO (4) <--> SDA
|
|
GPIO (5) <--> SCL
|
|
|
|
Power
|
|
3.3V <--> VIN
|
|
GND <--> GND
|
|
|
|
.. note:: If you have change the I2C settings in the hardware setup you need to connect to those instead of GPIO 4 and 5.
|
|
|
|
Setup
|
|
-----
|
|
|
|
.. image:: P028_Setup_BME280_1.png
|
|
|
|
Task settings
|
|
~~~~~~~~~~~~~
|
|
|
|
* **Device**: Name of plugin
|
|
* **Name**: Name of the task (example name **BME**)
|
|
* **Enable**: Should the task be enabled or not
|
|
|
|
Sensor
|
|
^^^^^^
|
|
|
|
* **i2C address**: You can use two BME280 at the same time, choose address here. If you only use one, stay with the default address.
|
|
* **Altitude**: Set the level above sea for your unit. This is done in order to get a correct pressure value.
|
|
* **Temperature offset**: Linear software calibration. One tenth of a degree Celsius, used to compensate for deviation of real temperature.
|
|
|
|
Data acquisition
|
|
^^^^^^^^^^^^^^^^
|
|
|
|
* **Send to controller** 1..3: Check which controller (if any) you want to publish to. All or no controller can be used.
|
|
* **Interval**: How often should the task publish its value (5..15 seconds is normal).
|
|
|
|
Indicators (recommended settings)
|
|
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
|
|
|
|
.. csv-table::
|
|
:header: "Indicator", "Value Name", "Interval", "Decimals", "Extra information"
|
|
:widths: 8, 5, 5, 5, 40
|
|
|
|
"Temperature", "Celsius", "10", "1", ""
|
|
"Humidity", "RH", "10", "0", ""
|
|
"Pressure", "hPa", "10", "0", ""
|
|
|
|
Rules examples
|
|
--------------
|
|
|
|
.. code-block:: none
|
|
|
|
on BME#hPa do
|
|
if BME#hPa>999
|
|
Publish,%sysname%/pressure,Is normal
|
|
endif
|
|
endon
|
|
|
|
.. Commands available
|
|
.. ~~~~~~~~~~~~~~~~~~
|
|
|
|
.. .. include:: P028_commands.repl
|
|
|
|
Change I2C address
|
|
------------------
|
|
|
|
You may change the i2c address from the default 0x76 to 0x77 by cutting the line between the two left pads (as seen in the pictures below) and solder a bridge between the two right pads.
|
|
|
|
.. image:: P028_BME280_2.jpg
|
|
|
|
Default i2c address 0x76.
|
|
|
|
.. image:: P028_BME280_3.jpg
|
|
|
|
Changed i2c address 0x77.
|
|
|
|
.. image:: P028_BME280_4.jpg
|
|
|
|
:green:`Cut` :red:`Solder/bridge`
|
|
|
|
Where to buy
|
|
------------
|
|
|
|
.. csv-table::
|
|
:header: "Store", "Link"
|
|
:widths: 5, 40
|
|
|
|
"AliExpress","`Link 1 ($) <http://s.click.aliexpress.com/e/sZWPuEM>`_"
|
|
"Banggood","`Link 2 ($) <https://www.banggood.com/CJMCU-280E-BME280-High-Precision-Atmospheric-Pressure-Sensor-For-Arduino-p-1103115.html?p=V3270422659778201806>`_ `Link 3 ($) <https://www.banggood.com/CJMCU-BME280-Embedded-High-Precision-Atmospheric-Pressure-Altitude-Sensor-Module-For-Arduino-p-1103112.html?p=V3270422659778201806>`_"
|
|
"eBay","`Link 4 ($) <https://rover.ebay.com/rover/1/711-53200-19255-0/1?icep_id=114&ipn=icep&toolid=20004&campid=5338336929&mpre=https%3A%2F%2Fwww.ebay.com%2Fsch%2Fi.html%3F_from%3DR40%26_trksid%3Dm570.l1313%26_nkw%3DBME280%26_sacat%3D0%26LH_TitleDesc%3D0%26_osacat%3D0%26_odkw%3DINA219>`_"
|
|
|
|
|affiliate|
|
|
|
|
|
|
.. More pictures
|
|
.. -------------
|
|
|
|
.. .. image:: P028_BME280_5.jpg
|