mirror of
https://github.com/Seeed-Studio/Seeed_Arduino_CAN.git
synced 2026-07-28 04:06:45 +00:00
89 lines
2.5 KiB
Arduino
89 lines
2.5 KiB
Arduino
// demo: CAN-BUS Shield, receive data with interrupt mode
|
||
// when in interrupt mode, the data coming can't be too fast, must >20ms, or else you can use check mode
|
||
// loovee, 2014-6-13
|
||
|
||
#include <SPI.h>
|
||
|
||
#define CAN_2515
|
||
// #define CAN_2518FD
|
||
|
||
// Set SPI CS Pin according to your hardware
|
||
|
||
#if defined(SEEED_WIO_TERMINAL) && defined(CAN_2518FD)
|
||
// For Wio Terminal w/ MCP2518FD RPi Hat：
|
||
// Channel 0 SPI_CS Pin: BCM 8
|
||
// Channel 1 SPI_CS Pin: BCM 7
|
||
// Interupt Pin: BCM25
|
||
const int SPI_CS_PIN = BCM8;
|
||
const int CAN_INT_PIN = BCM25;
|
||
#else
|
||
|
||
// For Arduino MCP2515 Hat:
|
||
// the cs pin of the version after v1.1 is default to D9
|
||
// v0.9b and v1.0 is default D10
|
||
const int SPI_CS_PIN = 9;
|
||
const int CAN_INT_PIN = 2;
|
||
#endif
|
||
|
||
|
||
#ifdef CAN_2518FD
|
||
#include "mcp2518fd_can.h"
|
||
mcp2518fd CAN(SPI_CS_PIN); // Set CS pin
|
||
#endif
|
||
|
||
#ifdef CAN_2515
|
||
#include "mcp2515_can.h"
|
||
mcp2515_can CAN(SPI_CS_PIN); // Set CS pin
|
||
#endif
|
||
|
||
|
||
unsigned char flagRecv = 0;
|
||
unsigned char len = 0;
|
||
unsigned char buf[8];
|
||
char str[20];
|
||
|
||
void setup() {
|
||
SERIAL_PORT_MONITOR.begin(115200);
|
||
while (!SERIAL_PORT_MONITOR. {
|
||
; // wait for serial port to connect. Needed for native USB port only
|
||
}
|
||
attachInterrupt(digitalPinToInterrupt(CAN_INT_PIN), MCP2515_ISR, FALLING); // start interrupt
|
||
while (CAN_OK != CAN.begin(CAN_500KBPS)) { // init can bus : baudrate = 500k
|
||
SERIAL_PORT_MONITOR.println("CAN init fail, retry...");
|
||
delay(100);
|
||
}
|
||
SERIAL_PORT_MONITOR.println("CAN init ok!");
|
||
}
|
||
|
||
void MCP2515_ISR() {
|
||
flagRecv = 1;
|
||
}
|
||
|
||
void loop() {
|
||
if (flagRecv) {
|
||
// check if get data
|
||
|
||
flagRecv = 0; // clear flag
|
||
SERIAL_PORT_MONITOR.println("into loop");
|
||
// iterate over all pending messages
|
||
// If either the bus is saturated or the MCU is busy,
|
||
// both RX buffers may be in use and reading a single
|
||
// message does not clear the IRQ conditon.
|
||
while (CAN_MSGAVAIL == CAN.checkReceive()) {
|
||
// read data, len: data length, buf: data buf
|
||
SERIAL_PORT_MONITOR.println("checkReceive");
|
||
CAN.readMsgBuf(&len, buf);
|
||
|
||
// print the data
|
||
for (int i = 0; i < len; i++) {
|
||
SERIAL_PORT_MONITOR.print(buf[i]); SERIAL_PORT_MONITOR.print("\t");
|
||
}
|
||
SERIAL_PORT_MONITOR.println();
|
||
}
|
||
}
|
||
}
|
||
|
||
/*********************************************************************************************************
|
||
END FILE
|
||
*********************************************************************************************************/
|