mirror of
https://github.com/Seeed-Studio/Seeed_Arduino_CAN.git
synced 2026-07-28 04:06:45 +00:00
70 lines
2.2 KiB
Arduino
70 lines
2.2 KiB
Arduino
// demo: CAN-BUS Shield, receive data with interrupt mode
|
|
// when in interrupt mode, the data coming can't be too fast, must >20ms, or else you can use check mode
|
|
// loovee, 2014-6-13
|
|
|
|
#include <SPI.h>
|
|
#include "mcp2518fd_can.h"
|
|
|
|
#define CAN_2518FD
|
|
|
|
// the cs pin of the version after v1.1 is default to D9
|
|
// v0.9b and v1.0 is default D10
|
|
const int SPI_CS_PIN = 9;
|
|
const int CAN_INT_PIN = 2;
|
|
|
|
#ifdef CAN_2518FD
|
|
mcp2518fd CAN(SPI_CS_PIN); // Set CS pin
|
|
#endif
|
|
|
|
unsigned char flagRecv = 0;
|
|
unsigned char len = 0;
|
|
unsigned char buf[64];
|
|
char str[20];
|
|
|
|
void setup() {
|
|
SERIAL_PORT_MONITOR.begin(115200);
|
|
while (!SERIAL_PORT_MONITOR. {
|
|
; // wait for serial port to connect. Needed for native USB port only
|
|
}
|
|
attachInterrupt(digitalPinToInterrupt(CAN_INT_PIN), MCP2515_ISR, FALLING); // start interrupt
|
|
CAN.setMode(0);
|
|
while (0 != CAN.begin((byte)CAN_500K_1M)) { // init can bus : baudrate = 500k
|
|
SERIAL_PORT_MONITOR.println("CAN init fail, retry...");
|
|
delay(100);
|
|
}
|
|
SERIAL_PORT_MONITOR.println("CAN init ok!");
|
|
byte mode = CAN.getMode();
|
|
SERIAL_PORT_MONITOR.printf("CAN BUS mode = %d\n\r", mode);
|
|
}
|
|
|
|
void MCP2515_ISR() {
|
|
flagRecv = 1;
|
|
}
|
|
|
|
void loop() {
|
|
if (flagRecv) {
|
|
// check if get data
|
|
|
|
flagRecv = 0; // clear flag
|
|
SERIAL_PORT_MONITOR.println("into loop");
|
|
// iterate over all pending messages
|
|
// If either the bus is saturated or the MCU is busy,
|
|
// both RX buffers may be in use and reading a single
|
|
// message does not clear the IRQ conditon.
|
|
while (CAN_MSGAVAIL == CAN.checkReceive()) {
|
|
// read data, len: data length, buf: data buf
|
|
SERIAL_PORT_MONITOR.println("checkReceive");
|
|
CAN.readMsgBuf(&len, buf);
|
|
// print the data
|
|
for (int i = 0; i < len; i++) {
|
|
SERIAL_PORT_MONITOR.print(buf[i]); SERIAL_PORT_MONITOR.print("\t");
|
|
}
|
|
SERIAL_PORT_MONITOR.println();
|
|
}
|
|
}
|
|
}
|
|
|
|
/*********************************************************************************************************
|
|
END FILE
|
|
*********************************************************************************************************/
|