mirror of
https://github.com/Seeed-Studio/Seeed_Arduino_CAN.git
synced 2026-07-27 19:55:59 +00:00
107 lines
2.9 KiB
Arduino
107 lines
2.9 KiB
Arduino
// demo: CAN-BUS Shield, receive data and save to sd card, can.csv
|
||
// when in interrupt mode, the data coming can't be too fast, must >20ms, or else you can use check mode
|
||
// NOTE: Only CAN Bus Shield V2.0 has SD slot, for other versions, you need an SD card Shield as well
|
||
// loovee, Jun 12, 2017
|
||
|
||
#include <SPI.h>
|
||
#include <SD.h>
|
||
|
||
File myFile;
|
||
|
||
#define CAN_2515
|
||
// #define CAN_2518FD
|
||
|
||
// the cs pin of the version after v1.1 is default to D9
|
||
// v0.9b and v1.0 is default D10
|
||
|
||
// Set SPI CS Pin according to your hardware
|
||
// For Wio Terminal w/ MCP2518FD RPi Hat：
|
||
// Channel 0 SPI_CS Pin: BCM 8
|
||
// Channel 1 SPI_CS Pin: BCM 7
|
||
// Interupt Pin: BCM25
|
||
// *****************************************
|
||
// For Arduino MCP2515 Hat:
|
||
// SPI_CS Pin: D9
|
||
|
||
#ifdef CAN_2518FD
|
||
#include "mcp2518fd_can.h"
|
||
const int SPI_CS_PIN = 9;
|
||
const int CAN_INT_PIN = 2;
|
||
mcp2518fd CAN(SPI_CS_PIN); // Set CS pin
|
||
#endif
|
||
|
||
#ifdef CAN_2515
|
||
#include "mcp2515_can.h"
|
||
const int SPI_CS_PIN = 9;
|
||
const int CAN_INT_PIN = 2;
|
||
mcp2515_can CAN(SPI_CS_PIN); // Set CS pin
|
||
#endif // Set CS pin
|
||
|
||
unsigned char flagRecv = 0;
|
||
unsigned char len = 0;
|
||
unsigned char buf[8];
|
||
char str[20];
|
||
|
||
void setup() {
|
||
SERIAL_PORT_MONITOR.begin(115200);
|
||
attachInterrupt(digitalPinToInterrupt(CAN_INT_PIN), MCP2515_ISR, FALLING); // start interrupt
|
||
#ifdef CAN_2518FD
|
||
while (0 != CAN.begin((byte)CAN_500K_1M)) { // init can bus : baudrate = 500k
|
||
#else
|
||
while (CAN_OK != CAN.begin(CAN_500KBPS)) { // init can bus : baudrate = 500k
|
||
#endif
|
||
SERIAL_PORT_MONITOR.println("CAN init fail, retry...");
|
||
delay(100);
|
||
}
|
||
SERIAL_PORT_MONITOR.println("CAN init ok!");
|
||
|
||
if (!SD.begin(4)) {
|
||
SERIAL_PORT_MONITOR.println("SD init fail!");
|
||
while (1);
|
||
}
|
||
SERIAL_PORT_MONITOR.println("SD init OK.");
|
||
}
|
||
|
||
void MCP2515_ISR() {
|
||
flagRecv = 1;
|
||
}
|
||
|
||
void loop() {
|
||
if (flagRecv) {
|
||
// check if get data
|
||
|
||
flagRecv = 0; // clear flag
|
||
unsigned long id = 0;
|
||
|
||
myFile = SD.open("can.csv", FILE_WRITE);
|
||
|
||
// iterate over all pending messages
|
||
// If either the bus is saturated or the MCU is busy,
|
||
// both RX buffers may be in use and reading a single
|
||
// message does not clear the IRQ conditon.
|
||
while (CAN_MSGAVAIL == CAN.checkReceive()) {
|
||
// read data, len: data length, buf: data buf
|
||
CAN.readMsgBufID(&id, &len, buf);
|
||
|
||
SERIAL_PORT_MONITOR.print(id);
|
||
SERIAL_PORT_MONITOR.print(",");
|
||
myFile.print(id);
|
||
myFile.print(",");
|
||
|
||
for (int i = 0; i < len; i++) {
|
||
SERIAL_PORT_MONITOR.print(buf[i]);
|
||
SERIAL_PORT_MONITOR.print(",");
|
||
|
||
myFile.print(buf[i]);
|
||
myFile.print(",");
|
||
}
|
||
SERIAL_PORT_MONITOR.println();
|
||
myFile.println();
|
||
}
|
||
|
||
myFile.close();
|
||
}
|
||
}
|
||
|
||
// END FILE
|