mirror of
https://github.com/Seeed-Studio/Seeed_Arduino_CAN.git
synced 2026-07-27 19:55:59 +00:00
72 lines
1.9 KiB
Arduino
72 lines
1.9 KiB
Arduino
/*
|
||
This is an example of sending and receiving on its own, connect two channels to each other using jumpers.
|
||
*/
|
||
|
||
#include <SPI.h>
|
||
#include "mcp2518fd_can.h"
|
||
|
||
// Set SPI CS Pin according to your hardware
|
||
// For Wio Terminal w/ MCP2518FD RPi Hat：
|
||
// Channel 0 SPI_CS Pin: BCM 8
|
||
// Channel 1 SPI_CS Pin: BCM 7
|
||
// Interupt Pin: BCM25
|
||
// *****************************************
|
||
// For Arduino MCP2515 Hat:
|
||
// SPI_CS Pin: D9
|
||
|
||
const int SPI_CS_PIN_SEND = 9;
|
||
const int SPI_CS_PIN_RECEIVE = 10;
|
||
|
||
mcp2518fd CAN_SEND(SPI_CS_PIN_SEND);
|
||
mcp2518fd CAN_RECEIVE(SPI_CS_PIN_RECEIVE);
|
||
|
||
unsigned char len = 0;
|
||
unsigned char buf[8];
|
||
|
||
void setup() {
|
||
SERIAL_PORT_MONITOR.begin(115200);
|
||
while(!Serial); // wait for Serial
|
||
|
||
if (CAN_SEND.begin((byte)CAN_500K_1M) != 0 || CAN_RECEIVE.begin((byte)CAN_500K_1M) != 0) {
|
||
Serial.println("CAN-BUS initiliased error!");
|
||
while(1);
|
||
}
|
||
|
||
SERIAL_PORT_MONITOR.println("CAN init ok!");
|
||
}
|
||
|
||
unsigned char stmp[8] = {0, 0, 0, 0, 0, 0, 0, 0};
|
||
void loop() {
|
||
// send data: id = 0x00, standrad frame, data len = 8, stmp: data buf
|
||
stmp[7] = stmp[7] + 1;
|
||
if (stmp[7] == 100) {
|
||
stmp[7] = 0;
|
||
stmp[6] = stmp[6] + 1;
|
||
|
||
if (stmp[6] == 100) {
|
||
stmp[6] = 0;
|
||
stmp[5] = stmp[5] + 1;
|
||
}
|
||
}
|
||
|
||
CAN_SEND.sendMsgBuf(0x00, 0, 8, stmp);
|
||
delay(100); // send data per 100ms
|
||
SERIAL_PORT_MONITOR.println("CAN BUS sendMsgBuf ok!");
|
||
|
||
// ---------------------
|
||
|
||
if (CAN_MSGAVAIL == CAN_RECEIVE.checkReceive()) {
|
||
// read data, len: data length, buf: data buf
|
||
SERIAL_PORT_MONITOR.println("checkReceive");
|
||
CAN_RECEIVE.readMsgBuf(&len, buf);
|
||
// print the data
|
||
for (int i = 0; i < len; i++) {
|
||
SERIAL_PORT_MONITOR.print(buf[i]); SERIAL_PORT_MONITOR.print(" ");
|
||
}
|
||
SERIAL_PORT_MONITOR.println();
|
||
}
|
||
SERIAL_PORT_MONITOR.println("---LOOP END---");
|
||
}
|
||
|
||
// END FILE
|