mirror of
https://github.com/Seeed-Studio/Seeed_Arduino_CAN.git
synced 2026-07-27 19:55:59 +00:00
97 lines
2.4 KiB
Arduino
97 lines
2.4 KiB
Arduino
// demo: CAN-BUS Shield, receive data and save to sd card, can.csv
|
|
// when in interrupt mode, the data coming can't be too fast, must >20ms, or else you can use check mode
|
|
// NOTE: Only CAN Bus Shield V2.0 has SD slot, for other versions, you need an SD card Shield as well
|
|
// loovee, Jun 12, 2017
|
|
|
|
#include <SPI.h>
|
|
#include "mcp_can.h"
|
|
#include <SD.h>
|
|
|
|
/*SAMD core*/
|
|
#ifdef ARDUINO_SAMD_VARIANT_COMPLIANCE
|
|
#define SERIAL SerialUSB
|
|
#else
|
|
#define SERIAL Serial
|
|
#endif
|
|
|
|
File myFile;
|
|
|
|
// the cs pin of the version after v1.1 is default to D9
|
|
// v0.9b and v1.0 is default D10
|
|
const int SPI_CS_CAN = 9;
|
|
const int SPI_CS_SD = 4;
|
|
|
|
MCP_CAN CAN(SPI_CS_CAN); // Set CS pin
|
|
|
|
unsigned char flagRecv = 0;
|
|
unsigned char len = 0;
|
|
unsigned char buf[8];
|
|
char str[20];
|
|
|
|
void setup()
|
|
{
|
|
SERIAL.begin(115200);
|
|
|
|
while (CAN_OK != CAN.begin(CAN_500KBPS)) // init can bus : baudrate = 500k
|
|
{
|
|
SERIAL.println("CAN BUS Shield init fail");
|
|
SERIAL.println("Init CAN BUS Shield again");
|
|
delay(100);
|
|
}
|
|
SERIAL.println("CAN BUS Shield init ok!");
|
|
|
|
attachInterrupt(0, MCP2515_ISR, FALLING); // start interrupt
|
|
|
|
if (!SD.begin(4)) {
|
|
SERIAL.println("SD initialization failed!");
|
|
while(1);
|
|
}
|
|
SERIAL.println("SD initialization done.");
|
|
}
|
|
|
|
void MCP2515_ISR()
|
|
{
|
|
flagRecv = 1;
|
|
}
|
|
|
|
void loop()
|
|
{
|
|
if(flagRecv)
|
|
{ // check if get data
|
|
|
|
flagRecv = 0; // clear flag
|
|
unsigned long id= 0;
|
|
|
|
myFile = SD.open("can.csv", FILE_WRITE);
|
|
|
|
// iterate over all pending messages
|
|
// If either the bus is saturated or the MCU is busy,
|
|
// both RX buffers may be in use and reading a single
|
|
// message does not clear the IRQ conditon.
|
|
while (CAN_MSGAVAIL == CAN.checkReceive())
|
|
{
|
|
// read data, len: data length, buf: data buf
|
|
CAN.readMsgBufID(&id, &len, buf);
|
|
|
|
SERIAL.print(id);
|
|
SERIAL.print(",");
|
|
myFile.print(id);
|
|
myFile.print(",");
|
|
|
|
for(int i = 0; i<len; i++)
|
|
{
|
|
SERIAL.print(buf[i]);
|
|
SERIAL.print(",");
|
|
|
|
myFile.print(buf[i]);
|
|
myFile.print(",");
|
|
}
|
|
SERIAL.println();
|
|
myFile.println();
|
|
}
|
|
|
|
myFile.close();
|
|
}
|
|
}
|
|
|
|
// END FILE
|