* DALI: bind DALI-2 push button events to control gear targets
Add command DaliBind<1..8> <device>,<instance>,<target>,<mode> to link
push button events (IEC 62386-301) from an input device instance to a
control gear target. Modes are Toggle, On, Off, Up and Down; Up and Down
start a fade on button press and stop it on release. The first matching
binding is executed. DaliBind<x> 0 removes a binding and DaliBind alone
lists them all.
Bindings are stored in the DALI settings file, packed as one uint32 per
slot, so they survive a restart.
* Describe how start-up brightness stored differently per short addres vs dali groups
* DALI: decode and publish DALI-2 input device event messages
Input devices such as push buttons (IEC 62386-301), occupancy sensors
(303) and light sensors (304) communicate with 24-bit event messages.
Tasmota logged these frames at log level 4 and discarded them, so it
could not react to any DALI-2 switch or sensor on the bus.
Decode the 24-bit frame according to the five IEC 62386-103 addressing
schemes and publish the result for rules and MQTT, for example
{"DALI":{"Event":"0x82840B","Scheme":"Instance","Type":1,"Instance":1,
"Info":11,"Name":"LongPressRepeat"}}
Push button events carry the part 301 event name, occupancy events the
Movement/Occupied/Repeat/Sensor flags and light sensor events the
Illuminance value. 24-bit frames with bit 16 set are commands from
another application controller and are ignored.
Tested with a zencontrol zc-switch rotary on an ESP32-S3-Pico with the
Waveshare Pico-DALI2, driving one channel of a DA4-T DT6 driver via
rules.
Co-Authored-By: Claude Fable 5.1 <noreply@anthropic.com>
* DALI: commission DALI-2 control devices and query their instances
Control devices (IEC 62386-103) such as push buttons and sensors are
addressed with 24-bit frames and have their own short address space,
separate from control gear. Until now they could only be commissioned
by hand with raw DaliSend255 frames.
Add DaliDeviceScan 1|2[,<max_count>] which assigns short addresses using
the 24-bit INITIALISE / RANDOMISE / COMPARE / PROGRAM SHORT ADDRESS
sequence. The existing binary search used by DaliScan is shared through
a device flag so control gear commissioning is unchanged. Mode 2 probes
the bus first so addresses already in use are never reassigned.
Add DaliDevice which lists addressed control devices, reports one
device's version, status and instances (type, enabled, event scheme),
and sets the event scheme of all its instances, for example
{"DaliDevice":{"Device":1,"Version":"2.0","Status":0,"Instances":[
{"Instance":0,"Type":1,"Name":"PushButton","Enabled":1,"Scheme":"Instance"}]}}
Input devices default to the Instance event scheme which carries no
short address, so DaliDevice <device>,2 switches them to DeviceInstance
events that identify the sending device.
---------
Co-authored-by: Claude Fable 5.1 <noreply@anthropic.com>
* Add Shelly emulation for ESP32 (EMUL_SHELLY)
Presents Tasmota as a generation 2 Shelly Pro 2PM to controllers
speaking the Shelly Gen2 RPC protocol, such as the Sigenergy
mySigen application.
The emulation follows Belkin WeMo and Hue Bridge: compiled in
with USE_EMULATION_SHELLY (ESP32 only, as it needs the IDF mDNS
component) and selected at runtime with `Emulation 3` or on the
Configure Other web page, where it appears as "Shelly single
device".
When selected, the driver advertises _shelly._tcp over mDNS with
the IPv4 and IPv6 addresses of all active interfaces and serves
/shelly and /rpc. Up to two switch, two input and two metering
channels are mapped onto Tasmota relays, switches and the energy
driver. Channels beyond the relays configured keep their state
in NVS so a controller still sees two working outputs.
Shelly controllers discard mDNS replies that do not carry the
RFC 6762 TTL of 255, which Espressif's mDNS component only sets
on multicast, so the driver raises the TTL on the mDNS sockets
after registration.
* Make Shelly emulation opt-in and renumber driver
Theo Arends
s-hadinger
John Murfett
Rene Hexel