pybricks-code/CHANGELOG.md

Changelog

Unreleased

Added

• Added better error message when no files to backup (support#681).

Fixed

• Fixed deleting files that are not open in the editor.

2.0.0-beta.3 - 2022-07-06

Changed

• Updated dependencies.

• Updated firmware to Pybricks v3.2.0b2:

  Added

  • Added Motor.stalled() method.

  Fixed

  • Fixed motor not stopping at the end of run_until_stalled (support#662).
  • Fixed incorrect battery current reading on Technic hub (support#665).
  • Fixed non-zero speed reported when motor stalled.
  • Fixed I/O devices not syncing at high baud rate.
  • Fixed ENODEV error while device connection manager is busy (support#674).

  Changed

  • Reworked internal motor model that is used to estimate speed.
  • Speed methods now use estimated speed instead of reported speed.
  • Changed drive base default speed to go a little slower.
  • Updated MicroPython to v1.19.

2.0.0-beta.2 - 2022-06-24

Added

• Added basic intellisense to the code editor.

2.0.0-beta.1 - 2022-06-03

Added

• Added multi-file support (support#418, support#465).

Changed

• Moved settings.

• Accessibility improvements.

• Updated dependencies.

• Updated documentation.

• Updated firmware to v3.2.0b1:

  Added

  • Added Stop.NONE as then option for motors.
  • Added Stop.COAST_SMART as then option for motors.
  • Made motor deceleration configurable separately from acceleration.
  • Enabled ujson module.
  • Added ability to use more than one DriveBase in the same script.
  • Added support for battery charging on Prime and essential hubs.

  Changed

  • Changed how DriveBases and Motor classes can be used together.
  • Raise asynchronous OSError instead of SystemExit if motor is disconnected while a program is running.
  • Changing settings while a motor is moving no longer raises an exception. Some settings will not take effect until a new motor command is given.
  • Disabled Motor.control and Motor.log on Move Hub to save space.
  • Changed LED color calibration on Prime hub to make yellow less green.
  • Updated to upstream MicroPython v1.18.
  • Changed imu.acceleration() units to mm/s/s (pybricks-micropython#88) for Move Hub, Technic Hub, and Prime Hub.

  Fixed

  • Fixed color calibration on Powered Up remote control (support#424).
  • Fixed 3x3 Light Matrix colors with hue > 255 not working correctly (support#619).

Fixed

• Fix tooltips not closing when expected (pybricks-code#275).

1.2.0-beta.1 - 2021-12-27

Added

• Status bar indicator for connected hub.
• Basic battery OK/low indicator (support#559).

Changed

• Saving file now uses proper save dialog in Chromium browser (support#84).
• Toolbar buttons now scale with screen size (support#300).

Fixed

• Fixed buttons wrong size while image is downloading (support#369).

1.1.0 - 2021-12-16

Changed

• Updated dependencies.

• Updated to Pybricks Firmware v3.1.0:

  Changed

  • Renamed new DCMotor.dc_settings() method to DCMotor.settings() (support#536).

  Fixed

  • Fixed direction for DriveBase.turn() and Drivebase.curve() for some arguments (support#535).
  • Fixed then=Stop.COAST not working in DriveBase methods (support#535).

• Updated docs:

  Added

  • Added maximum voltage setter for DCMotor and Motor.
  • Documented DriveBase.curve() method.

  Changed

  • Removed duty setting from Control.limits method.
  • Removed integral_range setting from Control.pid method.

1.1.0-rc.1 - 2021-11-19

Added

• Hub name setting for selecting hub name when flashing firmware (support#52).

Changed

• Updated to Pybricks firmware v3.1.0c1:

  Added

  • Added DriveBase.curve() method to drive an arc segment.
  • Added then and wait arguments to DriveBase methods (support#57).

  Changed

  • Dropped integral_range argument from Control.pid(). This setting was ineffective and never used. When set incorrectly, the motor could get stuck for certain combinations of kp and ki.
  • Improved motor behavior for cases with low-speed, low-load, but high inertia (support#366).
  • Changed how the duty cycle limit is set for Motor and DCMotor. It is now set as a voltage limit via a dedicated method, instead of Motor.control.

  Fixed

  • Fixed then=Stop.COAST being ignored in most motor commands.
  • Fixed brake()/light.off() not working on Move hub I/O port C (support#501).
  • Fixed Remote() failing to connect when hub is connected to 2019 or newer MacBooks (support#397).
  • Fixed intermittent improper detection of hot-plugged I/O devices (support#500).
  • A program now stops when a Motor is unplugged while it is running, instead of getting in a bad state.

• Updated docs:

  Added

  • Added ColorLightMatrix class.
  • Added LWP3Device class.

1.1.0-beta.6 - 2021-09-21

Added

• Show error message if connected hub is running old firmware (support#482).

Changed

• Updated dependencies.

• Updated to Pybricks firmware v3.1.0b1:

  Added

  • Support for LEGO Technic Color Light Matrix (support#440).
  • Support for LEGO UART devices with a new battery power flag. This is required to support the new LEGO Technic Color Light Matrix (support#440).
  • Support for the SPIKE Essential hub/Technic Small hub (support#439).

  Fixed

  • Fixed Ultrasonic Sensor and Color Sensor turning off when a user script ends (support#456).
  • Hub reset due to watchdog timer when writing data to UART I/O device (support#304).
  • City/Technic hubs not connecting via Bluetooth on macOS 12 (support#489).

  Changed:

  • Updated to MicroPython v1.17.

1.1.0-beta.5 - 2021-08-30

Changed

• Updated to Pybricks firmware v3.1.0a4:

  Added

  • Enabled builtin bytearray (pybricks-code#60).
  • Enabled ustruct module (pybricks-code#60).
  • Added alpha support for dual boot installation on the SPIKE Prime Hub.
  • Added pybricks.experimental.hello_world function to make it easier for new contributors to experiment with Pybricks using C code.
  • Added ability to import the main.mpy that is embedded in the firmware from a download and run program (support#408).
  • Added pybricks.iodevices.LWP3Device to communicate with a device that supports the LEGO Wireless Protocol 3.0.00 (pybricks-code#68)

  Changed

  • Move Hub Bluetooth optimizations to reduce firmware size (pybricks-code#49).
  • Disabled pybricks.iodevices module on Move Hub to reduce firmware size.
  • Improvements to pybricks.pupdevices.Remote:
    • Check if a remote is already connected before attempting to create a new connection.
    • Rename first argument from address to name to match documentation.
    • Implement connecting by name.
    • Add name() method.
    • Add light attribute.

• Updated documentation:

  Added

  • MicroPython module documentation.
  • Examples for hub system functions including stop button and shutdown.

  Changed

  • Build IDE docs as main docs with minor changes, instead of a completely separate build.
  • Moved motor control documentation to the motor page.

1.1.0-beta.4 - 2021-08-13

Fixed

• Fixed flashing firmware on Android support#403.

Changed

• Checksum is now validated as firmware flash progresses instead of just at the end support#433.
• About menu now shows firmware version as main version support#412.

1.1.0-beta.3 - 2021-07-20

Changed

• Changed snippet (autocomplete) content and behavior pybricks-code#471.
• Changed gutter background color pybricks-code#472.
• Added BETA badge to application icon support#375.
• Updated hub firmware to v3.1.0a3.

Fixed

• Fixed auto-indent not working pybricks-code#470.

1.1.0-beta.2 - 2021-07-06

Changed

• Changed from Ace editor to Monaco editor.
• Updated hub firmware to v3.1.0a2.

Fixed

• Fixed run button still enabled after hub disconnects during download support#378.

1.1.0-beta.1 - 2021-06-23

Changed

• Updated projects URL.
• Updated hub firmware to v3.1.0a1.
• Updated docs.

1.0.0 - 2021-06-08

Added

• Added changelog link to about dialog.

Changed

• Updated hub firmware to v3.0.0.
• Updated documentation.

Prerelease

Prerelease changes are documented at support#48.