The lookup of a function call based on a command string is known at compile time, so no need to keep track of this in memory.
This saves about 2200 bytes of RAM.
The strings alone account for close to 800 bytes (not using F() macro) and they are also being stored in the map.
So that's about 1600 bytes.
The extra 400 bytes are probably the pointers being stored in the map.
For .h files, it is common practice to add #ifndef #def statements around the implementation to prevent compiler issues when a file might be included twice.
VScode + PlatformIO needs the monitor_speed setting to be able to monitor the connected node. (default 9600 baud)
Also set the ESP8266 code base to 1.7.2
This plugin works on my test setup for more than 6 months and is by far the most stable node. (system uptimes of > 110 days)
So this may be considered stable.
The Json data has more items at the level of `data.Sensors[c]` thus must check if it is a TaskValues item.
Otherwise the values shown on Device page will not be updated.
With the newer Platform IO versions, builds failed because of wrong size set in board definition of ESP8285 board.
The PlatformIO settings labels have changed.
A failing ping may also halt the ESP node and some services may not return a ping, or ICMP packets may be filtered out on some connections.
See issue #1494.
Ammended central I2C functions with 16bit write and 32 bit read.
also added "false" parameter to wire.endTransmission before wire.request form
all as discussed in #1417
The plugin BMx280 can handle BMP280 and BME280.
The BMP version has no humidity sensor.
For Domoticz you have to send the data formatted differently.
Now the same plugin can be used for both BME280 and BMP280 and the settings in Domoticz can be set accordingly.
Previously the I2C registers containing measurement data was read per address at once.
Now all are read in one I2C command and then processed.
Also changed the source to be able to support multiple instances of the same task.
This should also fix #1381.
There is something strange about the handling of micros() timers in `NewPingESP8266`.
For this reason I added also a timeout based on `millis()`.
Adding an existing and proven I2C library.
Will need to test if this is working fine on ESP32 too and try to move I2C functionality to use these functions.
In order to semplify the setup of new units, I have added the following commands for modifying settings though serial port:
gateway (x.x.x.x)
dns (x.x.x.x)
subnet (x.x.x.x)
dst (0 or 1)
mqttretainflag (0 or 1)
messagedelay (ms)
ntphost (url)
timezone (minutes)
udpport (port number)
usentp (0 or 1)
work in serial and rules
Suppose you have two oled task with name FrontPanel and BackPanel. If you want turn off FrontPanel and print on BackPanel "Hi" at posintion 0,0 you must use the following instructions:
frontpanel.oledcmd off
backpanel.oled 0,0,Hi
if task name have space you must surround with square brackets. es: [task with space].oledcmd off
The /json page now also supports a limited view for the device page sensor updates.
The supported URLs for the json page are:
- `/json` All information in JSON format.
- `/json?view=sensorupdate` Limited view only for auto update on Devices tab.
- `/json?tasknr=N` with N being the task number, just outputs the information for the given task number.
N.B. these parameters can be combined, like: `/json?tasknr=1&view=sensorupdate`
Not sure how, but the headers of new JSON message can corrupt the buffer in the web log buffer.
In this attempt the log buffer lines are now moved to heap instead of stack.
Also the streaming webserver is given a bit more time to handle requests.
Steps to reproduce:
Set web log level to maximum and open web log viewer.
Then wait a few seconds to minutes to let the JSON stream stop and look at the last sent Json message. This will contain some typical Json web headers and thus no valid Json anymore.
Also added a quick fix for #1419
Previously I thought the body wasn't working correctly in email, however it was, with the exception of line breaks for text/html that have to be rewritten.
In communicating with the server, the sender and receiver needed to be surrounded by <> to be RFC2821 compliant.
The message body was coming out blank as an empty string was being sent instead of the correct string.
New Transformations:
#H: Hot/Cold
#A: Man/Auto
#a: M/A
New Justifications:
#Lx: Left (x=number of chars)
#Rx: Right (x=number of chars)
#Ux.y: Substring (x=first char; y=number of chars)
Plugin_041_update was being called before the plugin has been initialized, this resulted in an exception 28 type crash. Plugin_041_update clears the display and isn't required at the time of webform save.
This one is not yet complete, way more features and improvements are coming.
But for now it is already much much better than the old log viewer :)
So I'll merge it now and we'll see what it will become.
See #1351
Whenever a plugin_write returns success = true, the execute command will no longer be called.
It doesn't matter whether the plugin is enabled or present.
It should only return success = true when the command was actually meant for this plugin.
Previously the moment a timed function was called, the new timer was set. That would make the timer interval to be the minimum interval, with quite some margin of error.
Now the timers are at a more strict interval, unless the device cannot keep up.
See #1296
Rules got truncated when trying to save rules > 1520 Bytes.
Also added a bit more log information and some details about the used libraries in the sysinfo page and json output.
The reason is that inside PLUGIN_WRITE the variable [event->BaseVarIndex] is not set and is always = 0.
So actually this PR modifies the 1st value of task 1 and not the encoder counter.
Line 183 of P059_Encoder.ino should be removed:
UserVar[event->BaseVarIndex] = (float) event->Par1;
Apparently static IP needs to have IP config set before and after connection has been made.
The beginning is needed to make sure no DHCP client is started.
The second one is needed to make sure the wifi status is correct in the core library.
Many self compilers are reporting stuff, it's near to impossible to also support these since the different environments are so hard to set up for us developers to test.
I noticed that my latest commit introduced a small issue with Transformations:
The previous transformations were right justified. The new ones are left justified.
To maintain backwards compatibility I have modified the code.
- Reset wifi when DNS lookup returns *.0.0.0 (NTP lookup sometimes returns like these)
- Accept Wifi events out of order.
- Remove CRC from settings struct
- Patch settings with last few added items initialized
- Changed red question mark to white questionmark, for links to wiki.
Add core information to the log and info page
Add "more info" button to main page
Add question mark link button to sysinfo section describing wifi. This links to the wifi page on the wiki.
Message is sent to provide feedback on pressing the 'submit' button.
At that moment, it is not yet clear the data will be saved successful.
To prevent "Settings Saved" and "Error writing to..." to show on the same page, this text was changed.
See [this bug report](https://github.com/esp8266/Arduino/issues/4114), which is not fixed in 2.4.0.
This work-around will make sure no dhcp-client will be started when connecting to a network.
The active DHCP client could result in IP conflicts, difficulty in reconnect and other strange issues.
Sending LOG_LEVEL_ERROR as syslog error, LOG_LEVEL_INFO as syslog notice, and everything else as syslog deug
Also added Settings.Syslogfacility setting to be able to choose kernel (still default), user, daemon, message and local0-local7
Added Nextion plugin for testing from the Playground.
It is not yet tested on real hardware, but it has been in development for a while on the forum and playground.
Also requested in issue #1256 and by several others.
When a fixed IP setting is used, there will be no "Got IP" event, which will lead to a timeout and thus reconnect.
As a fix, the "Connected" event will also act like when a "Got IP" event was received when configured to use static IP.
A lot of issue reports do not include information about the used version of the core libraries and 'normal', 'dev', etc.
Since this information helps narrowing down the possible causes of the reported issues, it is best to add them in the general log.
I finally have one node acting as described by others and this one reported a disconnect before a connect attempt was made.
Now forcing the wifi in STA mode, should resolve this issue.
WiFi persistent settings were disabled after initialisation of the event handler.
This allowed the firmware to start WiFi connection with settings stored in the flash (not our settings, the settings kept by the core library). If these fail, then a connection failed event would occur before a connect attempt was started from ESPeasy, which would lead to strange results on some nodes while others work just fine.
A lot of functions in Webserver.ino were just appending to a ever increasing string. These strings were eventually sent to TXBuffer of the Webinterface.
So why not directly send them to the streaming buffer and thus reduce memory usage and gain speed.
A lot of functions in Webserver.ino were just appending to a ever increasing string. These strings were eventually sent to TXBuffer of the Webinterface.
So why not directly send them to the streaming buffer and thus reduce memory usage and gain speed.
The settings had 2 new values which would be overwriten by the checksum and there was still some issue about when to save the settings.
Also added a check to only save changed settings.
Known issue:
Sometimes after initial setup of wifi credentials, it is best to perform a reset.
Still existing problems:
- Credentials are not being saved from web interface and thus connection doesn't work from setup page.
- First time connect to SoftAP takes a lot of attempts, when the wifi was searching for an existing accesspoint. This searching does prevent the SoftAP to form a stable connection to the client.
Maybe the entire wifi stack has to be reset before switching to SoftAP. Now it is near to impossible to recover from incorrect settings or a changes accesspoint.
Still under investigation.
It looks to be a problem with the
Since event based wifi, it became more apparent the ESP8266 has some issues with running AP and STA mode simultaneous.
It appears this can only work when the channel remains constant. But when trying to connect to an accesspoint that channel will change.
This means Soft AP and STA cannot be active at the same time when searching for an accesspoint to connect to. For example login to the Soft AP to correct some settings or replace an accesspoint would not be possible.
This fix deals with all of these issues and keeps the fast try/fail connection attempts offered by the event based wifi.
In short:
- 3x attempt to connect to AP1 (each attempt takes about 2.5 seconds when failing)
- 3x attempt to connect to AP2
- Enable accesspoint
When accesspoint is active, the connect attempts will be done at a slower pace and STA mode is disabled. STA mode is also disabled as soon as someone connects to the Soft AP.
When the settings are saved, a retry to connect like normal is started almost immediately. N.B. This will result in a disconnect of the connected users to the Soft AP.
So the connection time is:
- AP1 is valid: 4 - 10 seconds
- AP1 is not valid, AP2 is: 12 - 20 seconds
- AP1 and AP2 are not valid: +/- 18 seconds before activating Soft AP
Since event based wifi, it became more apparent the ESP8266 has some issues with running AP and STA mode simultaneous.
It appears this can only work when the channel remains constant. But when trying to connect to an accesspoint that channel will change.
This means Soft AP and STA cannot be active at the same time when searching for an accesspoint to connect to. For example login to the Soft AP to correct some settings or replace an accesspoint would not be possible.
This fix deals with all of these issues and keeps the fast try/fail connection attempts offered by the event based wifi.
In short:
- 3x attempt to connect to AP1 (each attempt takes about 2.5 seconds when failing)
- 3x attempt to connect to AP2
- Enable accesspoint
When accesspoint is active, the connect attempts will be done at a slower pace and STA mode is disabled. STA mode is also disabled as soon as someone connects to the Soft AP.
When the settings are saved, a retry to connect like normal is started almost immediately. N.B. This will result in a disconnect of the connected users to the Soft AP.
So the connection time is:
- AP1 is valid: 4 - 10 seconds
- AP1 is not valid, AP2 is: 12 - 20 seconds
- AP1 and AP2 are not valid: +/- 18 seconds before activating Soft AP
In Deepsleep mode the wifi connect time is now minimum of 6 seconds.
Also the first loop after connect, the 'awake' timer will reset and start over. Without WiFi connection the set 'awake' timer starts at the moment the node boots.
While looking for issues regarding DeepSleep + MQTT and issue #1195, I came across a number of other issues related to high CPU load and WiFi disconnects when a MQTT controller cannot reach the MQTT broker or is set to be no longer enabled.
These fixes improve CPU load and WiFi stability and also send the following events:
- `MQTT#Connected`
- `MQTT#Disconnected`
- `MQTTimport#Connected`
- `MQTTimport#Disconnected`
The MQTTimport plugin still has some major issues which have to be taken care of, so #1195 is not fixed yet.
There is a problem with the PlatformIO builder since the last update of @mvdbro
It's an issue with the parsing of `#ifdef ESP32`.
It is very well explained here: [platformio/platformio-core#801 (comment)](https://github.com/platformio/platformio-core/issues/801#issuecomment-252447178)
In short, the event handling functions for the wifi have been moved to a separate .h file, since those files will be parsed properly by the Library Dependency Finder (LDF) in PlatformIO 3.x
While looking for issues regarding DeepSleep + MQTT and issue #1195, I came across a number of other issues related to high CPU load and WiFi disconnects when a MQTT controller cannot reach the MQTT broker or is set to be no longer enabled.
These fixes improve CPU load and WiFi stability and also send the following events:
- `MQTT#Connected`
- `MQTT#Disconnected`
- `MQTTimport#Connected`
- `MQTTimport#Disconnected`
The MQTTimport plugin still has some major issues which have to be taken care of, so #1195 is not fixed yet.
* Initial re-organisation of plugin sets (#1019)
* 12bit ADC values acceted up to 4095
MCP3221 is a 12bit ADC so accepted values should be up to 40195 not 1024
* automaticly updated release notes for v2.0-20180313
* - move all structs from ESPEasy.ino into header file
- add some fix for headers
- add const to rtttl notes array
* [issue #1066] Fix Webserver handle_control
There wasn't a proper start/end for the streaming webserver.
See discussion on issue #1066
* automaticly updated release notes for mega-20180314
* Custom controller GUI option
* Fixed #433
Not tested!
* #893, part 2 receiving
* Merge branch 'mega' of github.com:letscontrolit/ESPEasy into mega
# Conflicts:
# src/ESPEasy.ino
* Rules fix
* #893 part1, send messages
* Custom controller GUI option
* #893, part 2 receiving
* Rules fix
* automaticly updated release notes for mega-20180315
* - move all structs from ESPEasy.ino into header file
- add some fix for headers
- add const to rtttl notes array
* Merge branch 'mega' of github.com:letscontrolit/ESPEasy into mega
# Conflicts:
# src/ESPEasy.ino
* [v2.0 split globals] Base split on v2.0 version of ESPEasy.ino
* MCP3221 allow values for calibration (#1073)
MCP3221 allow values for calibration
* [issue #1066] Fix Webserver handle_control (#1079)
[issue #1066] Fix Webserver handle_control
* Fixed multi instance problem on SHT3x #433 (#1081)
Fixed multi instance problem on SHT3x #433
* [issue #1057] AM PM display issue
X:XX PM (for hours 1...9)
X:XX AM (for hours 1...9)
XX:XX PM (for hours 10...12)
XX:XX AM (for hours 10...12)
Added for H:MM (without seconds) notations:
- `%systm_hm%`
-`%systm_hm_am%`
* [issue #993] variable in MQTT subscribe topic
As [noted](https://github.com/letscontrolit/ESPEasy/issues/993#issuecomment-373140135) by @kluszcyn
* [issue #951] Changed System#Initialized => System#Wake
Changed System#Initialized => System#Wake
New event name makes more sense and Initialized may be used later to indicate all needed connections, etc. are ready.
* [issue #1057] AM PM display issue
X:XX PM (for hours 1...9)
X:XX AM (for hours 1...9)
XX:XX PM (for hours 10...12)
XX:XX AM (for hours 10...12)
Added for H:MM (without seconds) notations:
- `%systm_hm%`
-`%systm_hm_am%`
* [issue #993] variable in MQTT subscribe topic
As [noted](https://github.com/letscontrolit/ESPEasy/issues/993#issuecomment-373140135) by @kluszcyn
* [issue #951] Changed System#Initialized => System#Wake
Changed System#Initialized => System#Wake
New event name makes more sense and Initialized may be used later to indicate all needed connections, etc. are ready.
* automaticly updated release notes for mega-20180316
* automaticly updated release notes for v2.0-20180316
* Add download button for current rule set
* - add encoder write #1086
* changed memory tracker to uint64_t for the ESP32
* Changed so that running all tasks immediately with deep sleep enabled only happens on first iteration after wake up
* Keep uint. Just change the init value.
* [WiFi] Try to minimize effect of WiFi interruptions
And send event when connected to a different accesspoint.
Currently the impact on WiFi reconnects is enorm. The ESP stalls, won't react on events, etc.
* - fix success setting
* - fix P073 success setting in PLUGIN_WRITE callback
* - initialize pointer in P073
* [Relaxed WiFi] Perform WiFi initialization in steps
Doing WiFi initialization in multiple steps, will reduce boot time a lot.
For deepsleep the Setup is waiting for wifi initialization to complete, but for normal use the wifi connection is initiated during setup and checked on regular intervals to see if it is available.
The same for WiFi reconnect, which will hopefully not affect the performance of the ESP module during reconnects.
Also added a check + event when connected to another accesspoint with different BSSID (MAC address of accesspoint). Also the last used BSSID is used to reconnect to try to connect to the same device over and over, which may be useful with WiFi repeaters.
* [Travis error] Some #include test that wasn't meant to be included
... in the commit.
* [JSON] Add uint name (#1099) and WiFi information (PR #1113)
As suggested by @Grovkillen on PR #1113.
* [issue #1007] Allow user specific data in separate file
File will be ignored by git and can be simply included using `-D USE_OWN_DEFAULTS` in the build
* #ifndef instead of #ifdef
* [issue #1007] Add other defines as suggested by @uzi18
* [Memory] parseTemplate did not check if markers were found
"Free Mem" reported this function to be using quite a lot of memory.
Maybe that was related to parsing texts without matching ']' or '#'
Just added some checks to see if they were found.
* [issue #1097] MQTT publish after deep sleep
The MQTTConnect was only called after a while. This is a problem for deepsleep.
So now the MQTT connect is done at the first loop when deep sleep is enabled.
* Add download button for current rule set (#1102)
Add download button for current rule set
* - add encoder write command #1086 (#1103)
- add encoder write command #1086
* Changed so that running all tasks immediately with deep sleep enabled… (#1110)
Changed so that running all tasks immediately with deep sleep enabled only happens on first iteration after wake up
* Merge pull request #1112 from uzi18/fix-p073
Fix p073 - #1111
* Merge pull request #1114 from TD-er/feature/wifi_details_json
[JSON] Add uint name (#1099) and WiFi information (PR #1113)
* Merge pull request #1113 from TD-er/feature/reduce_impact_wifi_disconnect
[Relaxed WiFi] Perform WiFi initialization in steps
* Merge pull request #1116 from TD-er/feature/allow_own_defaults
[issue #1007] Allow user specific data in separate file
* Merge pull request #1118 from TD-er/bugfix/mqtt_publish_after_deep_sleep
[issue #1097] MQTT publish after deep sleep
* [merge] MIssing #endif due to merging.
* automaticly updated release notes for mega-20180319
* automaticly updated release notes for v2.0-20180319
* Fix wiring description for SN75176 transceiver
* Revert "Merge pull request #1116 from TD-er/feature/allow_own_defaults"
This reverts commit 8ccbdcadf0.
* Fix wiring description for SN75176 transceiver
* Revert "Merge pull request #1116 from TD-er/feature/allow_own_defaults"
This reverts commit 8ccbdcadf0.
* [issue #1097] WiFi connect with deepsleep enabled trigger watchdog reset
Did not allow for enough time to do background tasks while waiting for wifi connect with DeepSleep enabled.
* [issue #1097] WiFi connect with deepsleep enabled trigger watchdog reset
Did not allow for enough time to do background tasks while waiting for wifi connect with DeepSleep enabled.
* automaticly updated release notes for mega-20180320
* automaticly updated release notes for v2.0-20180320
* [wifi] Setup with factory settings could not complete
* [wifi] Setup with factory settings could not complete
* [merge issue] Forgotten #endif in merge
* - P012 fix command interpretation
* - P023 fix command interpretation
* - P035 move strings to flash
* - P048 fetch params only when needed
* automaticly updated release notes for mega-20180321
* automaticly updated release notes for v2.0-20180321
* Serial WD crash
* [wifi] Make more robust checks and increase timeout
See #1145
* - P012 fix command interpretation
* - P023 fix command interpretation
* - P035 move strings to flash
* - P048 fetch params only when needed
* Serial WD crash
* [wifi] Make more robust checks and increase timeout
See #1145
* [Memory] parseTemplate did not check if markers were found
"Free Mem" reported this function to be using quite a lot of memory.
Maybe that was related to parsing texts without matching ']' or '#'
Just added some checks to see if they were found.
* [WiFi] Take much more time for initial WiFi connect during setup
Accesspoint is still active, so it may take a lot more time to make the initial connection
* [WiFi] Take much more time for initial WiFi connect during setup
Accesspoint is still active, so it may take a lot more time to make the initial connection
* automaticly updated release notes for mega-20180322
* ESP32 fix
* [Command] Parsing improvement for commands
Use more intelligent parsing of commands and switch statement to improve speed
* automaticly updated release notes for mega-20180323
* [WiFi] Reverted those temp String uses for ssid/pass
Was introduced due to misunderstanding of reported issues with WiFi.
* [issue #1131] Add %unixtime%
Show the current time as [Unix time](https://en.wikipedia.org/wiki/Unix_time) (numbers of seconds that have elapsed since midnight 1970-01-01, UTC)
* [issue #1097] Call MQTTclient.loop() during deepsleep
The `MQTTclient.loop()` function should be called quite often.
This does the actual MQTT handling.
In normal operations, this is called quite frequently, but it should also be called when deepsleep is active and right before deepsleep is activated again.
* [P1] Support for latest standard
* [wifi] Event based connect/reconnect
Now using the core WiFiEvents to act on:
- connect
- disconnect
- gotIP
This will make polling for a status no longer needed.
It also allows to get a better understanding in why diconnects happen, since the disconnect reason is given in the events.
This extra information is also present on the information panel on the webinterface and also in the JSON output.
The entire connect/disconnect/reconnect is now done completely asynchronous and thus takes much less resources from the ESP.
A disconnect will now also send an event: "WiFi#Disconnected"
For deepsleep this means there has to be a minimum awake time set and perhaps use rules to set the ESP into sleep again when done.
Typical connection times to an accesspoint are about 3 seconds + about 1 second for DHCP.
This also resolves the issues where services my try to connect while there is a WiFi connection, but not yet an IP address set.
I already noticed a lot of NTP servers from pool.ntp.org are non responsive the last few weeks, so that may still take some time, but that's another issue.
* automaticly updated release notes for mega-20180324
* [NTP] Speedup NTP again with async WiFi
Previously it would only start calling "now" when the WiFi was already setup.
And in calling `now()`, a call to an NTP server is being made. When this fails, retry again in a minute.
But now the WiFi initialization is asynchronous, so the first NTP query was already failing and thus the retry is already set to a minute.
This is fixed now and also the pool.ntp.org will pick a random one from 0...3 (.pool.ntp.org).
The DNS queries from this pool change about every minute, so if you want to retry because one of the servers is offline, you should try one from the other `N.pool.ntp.org` or else you have to wait for another minute.
* - fix for #1170 - uservar not setted on encwrite
* automaticly updated release notes for mega-20180326
* [issue #1174] Show degree sign via external writes to LCD
Fix suggested by [elmicha](https://github.com/letscontrolit/ESPEasy/issues/1174#issuecomment-376244766)
* [ESP32] Event driven WiFi for ESP32
Not tested, just got some inspiration by these files:
- https://github.com/espressif/arduino-esp32/blob/master/libraries/WiFi/examples/WiFiClientEvents/WiFiClientEvents.ino
- https://github.com/espressif/arduino-esp32/blob/master/libraries/WiFi/src/WiFiGeneric.cpp
- https://github.com/espressif/arduino-esp32/blob/master/tools/sdk/include/esp32/esp_event.h
* automaticly updated release notes for mega-20180327
* Fix nesting level check
* [Build] Cleanup/split builds using defines
See PR #1034 and #1040 made by @soif
* [build] Disabled a few PlatformIO profiles for now.
There were way too many.
Just placed them in comments and Travis had already built them all to test first.
* automaticly updated release notes for mega-20180328
* [Arduino IDE] Revert changes in include paths
Were changed to be able to test the PlatformIO feature to compile only files that are actually used.
Apparently the Arduino IDE cannot find the files anymore because that IDE needs the parent directory to be named as the main project file, not "src"
* automaticly updated release notes for mega-20180329
Were changed to be able to test the PlatformIO feature to compile only files that are actually used.
Apparently the Arduino IDE cannot find the files anymore because that IDE needs the parent directory to be named as the main project file, not "src"
Previously it would only start calling "now" when the WiFi was already setup.
And in calling `now()`, a call to an NTP server is being made. When this fails, retry again in a minute.
But now the WiFi initialization is asynchronous, so the first NTP query was already failing and thus the retry is already set to a minute.
This is fixed now and also the pool.ntp.org will pick a random one from 0...3 (.pool.ntp.org).
The DNS queries from this pool change about every minute, so if you want to retry because one of the servers is offline, you should try one from the other `N.pool.ntp.org` or else you have to wait for another minute.
Now using the core WiFiEvents to act on:
- connect
- disconnect
- gotIP
This will make polling for a status no longer needed.
It also allows to get a better understanding in why diconnects happen, since the disconnect reason is given in the events.
This extra information is also present on the information panel on the webinterface and also in the JSON output.
The entire connect/disconnect/reconnect is now done completely asynchronous and thus takes much less resources from the ESP.
A disconnect will now also send an event: "WiFi#Disconnected"
For deepsleep this means there has to be a minimum awake time set and perhaps use rules to set the ESP into sleep again when done.
Typical connection times to an accesspoint are about 3 seconds + about 1 second for DHCP.
This also resolves the issues where services my try to connect while there is a WiFi connection, but not yet an IP address set.
I already noticed a lot of NTP servers from pool.ntp.org are non responsive the last few weeks, so that may still take some time, but that's another issue.
The `MQTTclient.loop()` function should be called quite often.
This does the actual MQTT handling.
In normal operations, this is called quite frequently, but it should also be called when deepsleep is active and right before deepsleep is activated again.
"Free Mem" reported this function to be using quite a lot of memory.
Maybe that was related to parsing texts without matching ']' or '#'
Just added some checks to see if they were found.
The MQTTConnect was only called after a while. This is a problem for deepsleep.
So now the MQTT connect is done at the first loop when deep sleep is enabled.
"Free Mem" reported this function to be using quite a lot of memory.
Maybe that was related to parsing texts without matching ']' or '#'
Just added some checks to see if they were found.
Doing WiFi initialization in multiple steps, will reduce boot time a lot.
For deepsleep the Setup is waiting for wifi initialization to complete, but for normal use the wifi connection is initiated during setup and checked on regular intervals to see if it is available.
The same for WiFi reconnect, which will hopefully not affect the performance of the ESP module during reconnects.
Also added a check + event when connected to another accesspoint with different BSSID (MAC address of accesspoint). Also the last used BSSID is used to reconnect to try to connect to the same device over and over, which may be useful with WiFi repeaters.
And send event when connected to a different accesspoint.
Currently the impact on WiFi reconnects is enorm. The ESP stalls, won't react on events, etc.
Changed System#Initialized => System#Wake
New event name makes more sense and Initialized may be used later to indicate all needed connections, etc. are ready.
Changed System#Initialized => System#Wake
New event name makes more sense and Initialized may be used later to indicate all needed connections, etc. are ready.
According to the MH-Z19B data sheet version 1.2, valid from: 2017.03.22 (received 2018-03-07), the offset should be [6]..[7] instead.
Fixing the implementation accordingly.
Changed the sleep checkbox to allow a number of seconds awake from deep sleep.
Also added the following events:
- MQTT#Connected
- WiFi#Connected
- System#Initialized
- Time#Set Time set by an update from NTP.
- Time#Initialized Time set for the first time since boot.
- Login#Failed
See #951
Changed the sleep checkbox to allow a number of seconds awake from deep sleep.
Also added the following events:
- MQTT#Connected
- WiFi#Connected
- System#Initialized
- Time#Set Time set by an update from NTP.
- Time#Initialized Time set for the first time since boot.
- Login#Failed
See #951
Also made some clean-up of calls to string replacements.
Improved the lookup function to determine the wind direction (was 11.25 degree off)
Now it is also possible to add simple standard conversions like Celcius-Fahrenheit, m/s - Beaufort, etc.
_P072_HDC1080 add success and break statement.
it seems that without the break statement and success set to true, the values aren't sent back to the controller(s).
_P072_HDC1080 add success and break statement.
it seems that without the break statement and success set to true, the values aren't sent back to the controller(s).
* - pcfgpio,port,2 sets pin as input
- fix for #222,#702 - we can mix inputs and outputs now
* - extend conditions with AND/OR, now it is possible to simplify rules
test rules:
on test do
if [test#a]=0 or [test#b]=0 or [test#c]=0
event ok
else
event nok
endif
endon
on test2 do
if [test#a]=1 and [test#b]=1 and [test#c]=1
event ok
else
event nok
endif
endon
on test3 do
if [test#a]=1 and [test#b]=1 or [test#c]=0
event ok
else
event nok
endif
endon
on test4 do
if [test#a]=0
event ok
else
event nok
endif
endon
* - remove Serial print
* - add format #O to templates to show OFF/ON instead 0/1 - eg.: Pump:[Outputs#pump#O]
* - add formating for active low outputs eg.: #O!
- Use peek instead of read, to make sure a complete packet is in the buffer.
- Flush buffer after processing a packet.
- Increased software serial buffer to the size of 3 packets.
- Peek (+ read garbage) 10 times per second to get the buffer in sync to start with start byte of packet.
- Decent delete + clean up of software serial allocation when changing settings (prevent memory leak)
- Move log String allocation to inside scope of function, not permanent allocated.
- Split into separate functions to make it better readable.
* - pcfgpio,port,2 sets pin as input
- fix for #222,#702 - we can mix inputs and outputs now
* - extend conditions with AND/OR, now it is possible to simplify rules
test rules:
on test do
if [test#a]=0 or [test#b]=0 or [test#c]=0
event ok
else
event nok
endif
endon
on test2 do
if [test#a]=1 and [test#b]=1 and [test#c]=1
event ok
else
event nok
endif
endon
on test3 do
if [test#a]=1 and [test#b]=1 or [test#c]=0
event ok
else
event nok
endif
endon
on test4 do
if [test#a]=0
event ok
else
event nok
endif
endon
* - remove Serial print
* - add format #O to templates to show OFF/ON instead 0/1 - eg.: Pump:[Outputs#pump#O]
* - add formating for active low outputs eg.: #O!
* - fix #964, add timeStringToSeconds and use it to compare time conditions
* - fix number of pages available to browse
* - pcfgpio,port,2 sets pin as input
- fix for #222,#702 - we can mix inputs and outputs now
* - extend conditions with AND/OR, now it is possible to simplify rules
test rules:
on test do
if [test#a]=0 or [test#b]=0 or [test#c]=0
event ok
else
event nok
endif
endon
on test2 do
if [test#a]=1 and [test#b]=1 and [test#c]=1
event ok
else
event nok
endif
endon
on test3 do
if [test#a]=1 and [test#b]=1 or [test#c]=0
event ok
else
event nok
endif
endon
on test4 do
if [test#a]=0
event ok
else
event nok
endif
endon
* - remove Serial print
* - add format #O to templates to show OFF/ON instead 0/1 - eg.: Pump:[Outputs#pump#O]
* - add formating for active low outputs eg.: #O!
* - pcfgpio,port,2 sets pin as input
- fix for #222,#702 - we can mix inputs and outputs now
* - extend conditions with AND/OR, now it is possible to simplify rules
test rules:
on test do
if [test#a]=0 or [test#b]=0 or [test#c]=0
event ok
else
event nok
endif
endon
on test2 do
if [test#a]=1 and [test#b]=1 and [test#c]=1
event ok
else
event nok
endif
endon
on test3 do
if [test#a]=1 and [test#b]=1 or [test#c]=0
event ok
else
event nok
endif
endon
on test4 do
if [test#a]=0
event ok
else
event nok
endif
endon
* - remove Serial print
* - add format #O to templates to show OFF/ON instead 0/1 - eg.: Pump:[Outputs#pump#O]
* - add formating for active low outputs eg.: #O!
* - fix #964, add timeStringToSeconds and use it to compare time conditions
* - fix number of pages available to browse
* - pcfgpio,port,2 sets pin as input
- fix for #222,#702 - we can mix inputs and outputs now
* - extend conditions with AND/OR, now it is possible to simplify rules
test rules:
on test do
if [test#a]=0 or [test#b]=0 or [test#c]=0
event ok
else
event nok
endif
endon
on test2 do
if [test#a]=1 and [test#b]=1 and [test#c]=1
event ok
else
event nok
endif
endon
on test3 do
if [test#a]=1 and [test#b]=1 or [test#c]=0
event ok
else
event nok
endif
endon
on test4 do
if [test#a]=0
event ok
else
event nok
endif
endon
* - remove Serial print
* - add format #O to templates to show OFF/ON instead 0/1 - eg.: Pump:[Outputs#pump#O]
* - add formating for active low outputs eg.: #O!
See #922 and #847
Problem with DNS resolve is that it is quite slow when resulting in a failure and it tends to keep the ESP occupied and make it unresponsive.
Changed the way it is connecting to a controller.
Not sure if http requests are still OK, maybe we should make an exception for those when selected to use DNS.
* - pcfgpio,port,2 sets pin as input
- fix for #222,#702 - we can mix inputs and outputs now
* - extend conditions with AND/OR, now it is possible to simplify rules
test rules:
on test do
if [test#a]=0 or [test#b]=0 or [test#c]=0
event ok
else
event nok
endif
endon
on test2 do
if [test#a]=1 and [test#b]=1 and [test#c]=1
event ok
else
event nok
endif
endon
on test3 do
if [test#a]=1 and [test#b]=1 or [test#c]=0
event ok
else
event nok
endif
endon
on test4 do
if [test#a]=0
event ok
else
event nok
endif
endon
* - remove Serial print
test rules:
on test do
if [test#a]=0 or [test#b]=0 or [test#c]=0
event ok
else
event nok
endif
endon
on test2 do
if [test#a]=1 and [test#b]=1 and [test#c]=1
event ok
else
event nok
endif
endon
on test3 do
if [test#a]=1 and [test#b]=1 or [test#c]=0
event ok
else
event nok
endif
endon
on test4 do
if [test#a]=0
event ok
else
event nok
endif
endon
* preparations for lwip2
* Add CRC32 to settings
* Add CRC to progmem
* Add crc of program memory to stettings and security settings
.. so that there is a warning if the settings are used by another binary than they were written with.
* Moved to md5
* Flash included, moved to MD5 now
* Broken comment
* Stability improvements
free memory went as low as 3000 bytes which made the webserver unresponsive.
* Add binary filename to crc2.py and sysinfo
* Update WebServer.ino
* Updating template structure, adding viewport meta name for mobile devices, feature ready for responsive layout
* Adding meta viewport, feature ready nad support for mobile devices, responsive layout, update template structure, adding article html5 tag, easier to style interface, find/replace uppercase to lowercase, matter of elegance and preference code readability :-)
* revert to default state and change only template related lines
* final check, revert uppercase
* Last template changes, lost in undo process :-)
* h6 footer TR
* [isue #877] Add VCC enable firmware file to release list
Added one for the testing build.
Not sure if we should add one for every build, since these flags will lead to an explosion of release versions.
But at least we will test builds with FEATURE_ADC_VCC define enabled more often.
* Add define FEATURE_ADC_VCC to the PUYA build
Since it is so hard to make a puya version on your own.
* [issue #890] Split overlap for both Domoticz controllers to helper
Both Domoticz controllers had quite some overlap in code.
And where they differ, one of them was faulty and/or already fixed.
Now this overlap is split into a Domoticz helper file to keep code duplication to a minimum.
* [issue #890] Fix some wierd data corruption
Do not store references in a Json object, but just the string :)
* [Domoticz] Add WiFi strength and battery info
%mac% will be replaced by the MAC-address of the ESP board.
%mac_int% will show the integer representation of the last 24 bits (MAC address without the OUI part) for use in rules.
* [issue #847 ] OpenHAB MQTT rewrite topic parser
When OpenHAB MQTT controller was selected, the web interface becomes unresponsive when the controller tab was selected.
Also the ESP almost freezes when MQTT messages were sent.
This is an attempt to make them work faster.
Also a lot of string manipulation, copies and resizes are now no longer needed and the received values are checked to be valid int or float before used.
* signed unsigned warning
* [issue #869] Added 'LWT' to last will topic and improved CPU load
See #869 for discussion on Last Will Topic.
Also changed the way it tried to reconnect to make it return a lot faster when connection is not (yet) possible and call the PubSubClient::loop() at a much slower pace to reduce CPU usage. (See #847)
This higher CPU load was probably introduced when fixing #683.
* [MQTT] Fix error reporting success status with longer payloads
Applied PR https://github.com/knolleary/pubsubclient/pull/360/files
* made MQTT_CALLBACK_SIGNATURE for esp32 functional
Applied PR https://github.com/knolleary/pubsubclient/pull/336
* [issue #853] Favicon.ico
Added a very small favicon.ico of the ESPeasy logo. (1150 Bytes, 16x16)
* [Favicon] Added instructions to change icon.
In the comments. Just use 'xxd' from the (Linux) commandline.
First attempt, not clear yet how to detect it.
See #866
Also preparation for future improvement on logging. (to detect whether there is some logging active so Strings may not have to be prepared.
* update Blynk controller
- use of real controller index
- we use idx
- check if password not empty
- use real password
* fix for Blynk Controller
- use of real controller index
- we use idx
- check if password not empty
- use real password
- use proper port
* Update _C012.ino
add SENSOR_TYPE_SWITCH support
* [v2.0] Blynk controller
* fix for Blynk Controller
- use of real controller index
- we use idx
- check if password not empty
- use real password
- use proper port
* Update _C012.ino
add SENSOR_TYPE_SWITCH support
- on 2.4.0 git /low mem LWIP ram goes never below 20k, during TX core dives down to 18,7k (each main menu clicked once, plain new config.)
- Fixed json output
- cleanup of send function#
- un-split css, transfer to buffer byte by byte (prevents 1.7k temporary string)
- removed commented-out function
Recent changes in 'early exit' when not connected, triggered lots of retry events.
Added some function to allow to wait for WiFi and in the meantime do some background tasks.
See #825
Added option for controllers to change their display string on some controller fields in the web interface.
When password field label is non-default it also implies to use a visible textfield instead of a password field.
Re-implementation of PR #482 which was done on Mega branch.
Just to keep merges simple between branches. (and improve readabilit)
Also added a simple check to C005 (OpenHAB MQTT) on receiving messages. (see #847 )
* [OLED] Move font to oled lib dir
It is specific for use wth that library.
* [OLED framed] Stop reading from flash constantly and live update WiFi
See #857
The OLED Framed plugin was reading from spiffs all of the time (on every display update)
Now the data is only read from SPIFFS when needed.
Also made the WiFi strength indicator update every second (only when changed) to be able to see changes in WiFi status much easier.
* Update Library LiquidCrystal_I2C to the latest version
* Fix LCD command (when message is longer than columns) that get split into the wrong lines - issue #603
* Added a "LCD command mode" parameter to handle how exceeding message would be treated, and if the line should be first padded with space.
It was causing issues when people upgraded from previous builds.
Leaving it would cause high CPU loads, instable wifi, and incorrect set switch type when upgrading from older builds.
Only thing is when people were using it as a dimmer and used one of the builds in the last few weeks.
Then it will be used as a 'switch', not a dimmer. Change and set and all is fine again.
* [issue #839] Add command support for setting contrast for OLED Framed
See #839
* [issue #839] Should not use 0 as off value, since that is default
With 0 as "off", the display would be off when not set.
Changed it to 1, which is not a value that can be set other than with the commands
* Blynk controler (re-implementation of PR#92)
See #92
This plugin is just ported from the old implementation, which was not merged into the Mega branch.
It now is using a lot of the newly created functions and optimizations.
But not yet tested.
* Update _C012.ino
memory never goes below 10k now.
Added wait for memory return on header send,
Added wait for memory return on chunk end send,
removed duplicate of data stashing with getWebPageTemplateVar
See #727
And it only took 4 bytes extra storage :)
When initialized with an invalid setting for DST, (like fresh after flashing), it will use the CEST/CET setting.
* [issue #817] Added mail header to SMTP
N.B. use only mail address (no name, no '<>' etc) as sender.
* [SMTP] Add user/pass to send email.
* [issue #817] Added user + passwd authentication to SMTP notifications
Tested with smtp2go.com (non TLS mail proxy)
It is now possible to add username + passwd when sending mail.
If both left empty, authentication will not be used.
As part of #698 and also since these system variable replacement may grow.
Some replacement strings may need some work to create and such effort is wasted if the matching string does not occur.
To improve this and still remain readable, I added a simple macro to check first and then create the strings only when needed.
Some strings are already present, so these do not use the macro since searching first and then look again to replace will take more effort.
* [#784] Add %rssi% as system variable
See #784
* [#787] Add %unit% and %ssid% system variable
See #787
Unit is the unit number of the ESP device.
SSID is the name of the WiFi accesspoint the ESP device is connected with.
* [issue #740] Allow MQTT controller to be on any controller
See #740
Still there is an issue when >1 MQTT controller is selected and enabled.
Currently only one MQTT controller may be active.
* [issue #740] Add warning when >1 MQTT controller is active
Add a warning to the web interface when >1 MQTT controller is active.
See #740
* [Mega] Force 2.3.0 for all builds and add an option for 2.4.0 core
This way we can test issues easier and people are still using 2.3.0 core version.
* Update platformio.ini
Environment labels should not use dots. Then they will not show in the build selection box.
* [V2.0] Allow IRremoteESP8266 to be build with core 2.4.0
A partial cherrypick of #772, to make merging easier.
Just some simple patches on the use of min() and max() in the library to allow it to compile using the 2.4.0 core lib. Actual use of this core lib is still prohibited by the check in ESPEasy.ino.
* [core 2.3.0] Force PlatformIO to use the 2.3.0 core libs
This update forces the PlatformIO environment to load the 1.5.0 version of espressif8266@1.5.0, which uses Core 2.3.0
Last few days, lots of issues reported by users who installed the 2.4.0 core libraries.
e.g. #769 and #763
It appeared the default PlatformIO Espressif 8266 1.6.0 libs now include the 2.4.0 core libraries.
Now I have to find a way to get my own environment back to the 2.3.0 core libs and see how I can get PlatformIO Espressif 8266 library back to version 1.5.0
* preparations for lwip2
* Add CRC32 to settings
* Add CRC to progmem
* Add crc of program memory to stettings and security settings
.. so that there is a warning if the settings are used by another binary than they were written with.
* Moved to md5
* Flash included, moved to MD5 now
* Broken comment
* preparations for lwip2
* Add CRC32 to settings
* Add CRC to progmem
* Add crc of program memory to stettings and security settings
.. so that there is a warning if the settings are used by another binary than they were written with.
* Moved to md5
* Flash included, moved to MD5 now
* Broken comment
* preparations for lwip2
* Add CRC32 to settings
* Add CRC to progmem
* Add crc of program memory to stettings and security settings
.. so that there is a warning if the settings are used by another binary than they were written with.
* Moved to md5
* Flash included, moved to MD5 now
* Central function for system variable replacement
Related to:
- #698 => Not complete
- #709 => fixed
- #751 => fixed
Redesign of PR #485 (in mega branch)
One note: no sensor values can be used in controllers. Is this what we want, or should we call parseTemplate everywhere parseSystemVariables is being used?
Also not all controllers apparently allow system variables. Is this also correct?
* [issue 757] Add %lcltime% to display date + time
As requested by @PsychoAndi at PR #757
* [issue 757] Add local time to JSON output
As suggested by @PsychoAndi
See #728
Also looked into the very strange configuration settings lookup for MQTT settings. The way it was, the settings for the first MQTT controller were used even when the actual MQTT controller was inactive or using different settings.
Now the controller selected in the the plugin is being used and when no plugin setting is available (and also for P037 MQTT import) the first active MQTT controller will be used.
* removed note for 74HC595
74HC595 pin reminder not needed as this chip won't be supported anymore
* deleted GPIO notes referring to 75HC595 not supported
* [Time] Moved time related code to separate file
* [AutoDST] Added Auto DST
Preliminary support for Auto DST, as requested in #569
Also did a little refactorin of time related code, with #698 in mind.
All time related code is split into a few files based on its function.
The currently selected DST will start on Last Sunday March 2am and end on Last Sunday October 3am.
This is the most frequently used DST, according to https://en.wikipedia.org/wiki/Daylight_saving_time_by_country
To change it, currently the code has to be changed in the function applyTimeZone(). Several examples are given right below that function.
Problem is where to store the information of the timezone, how to use it in the web interface and how convenient it is to set by hand.
The UTC offset in minutes still has to be entered and whether or not DST should be enabled.
Prevent sending of invalid values (NaN, inf) to any controller.
Simple test is to output any plugin value with formula set to "%value%/0" and try to send it to any controller.
Is a fix for #470 and #693
* [switch] Fixed switch behavior and default settings. (#675)
As described in #673 .
The problem was partly related to the default values stored in flash ("0"), which was not a valid value for the switch type.
When upgrading from an older version of ESPeasy, make sure to check the switch type (normal switch or dimmer) and save the settings for the switch device again, even when nothing was changed.
Default configuration and new added switches will now work like intended.
When a controller is enabled (e.g. Domoticz MQTT or -HTTP) and the button is pressed multiple times, the ESP may reboot. See issue #674.
* ABC calibration feature added (#606)
* [Flash info] Detailed flash information (#678)
Last few days a number of issues and forum topic was about the type of flash used on the ESP boards.
This is an extension of the detailed information page.
Perhaps also merge with the newer and more clear layout of pull request #624?
That pull request was only merged to the mega branch.
I kept the changes local, but perhaps they should be placed in the "Storage" section introduced with #624.
Maybe also that pull request should get merged into the v2.0 branch.
* Bugfix/v2.0 crash switch (#682)
* [crashes] Added constructors to initialize all members in structs
Numerous structs are defined, but none of them have default constructors and there is no guarantee the members will be set when used.
With these default constructors, the parameters at least have an initialized value.
* [PubSubClient] Add bound checks on the internal buffer
Not sure if this was really causing an issue, but proper bound checks are always a good thing.
* [Crash Switch] Disabled delayBackground and added yield() calls
Something really fishy is going on with the delayBackground function, which will result in crashes when pressing the switch multiple times, with Domoticz MQTT enabled as first controller.
Disabled for now and delay(1) added to give background tasks a chance to do their work and make sure the watchdog doesn't perform a reset.
* [CI build errors] Commented out some unused variables
Travis considers them as error and fails the checks.
* [CI check] Out-of-bounds check fix
* actually ignore MQTT messages that are too big.
* moved mqtt stuff outside of backgroundtasks(). fixes #683 in my test scenario
* [Adafruit MPR121] Change deprecated name setThreshholds to setThresholds (#685)
See #684
* fixed plugin id of "Communication - Kamstrup Multical 401". (accidental octal notation)
* changed devicecombobox handling to save a lot of memory on device page. fixes #654#676 and could be triggered by #683 in some cases.
* [CPPcheck] v2.0 ControllerSettingsStruct some variables not initialized (#692)
Fixing these cppcheck errors:
101.43s$ cppcheck --enable=warning src/*.ino -q --force -I src --include=src/ESPEasy.ino --error-exitcode=1
[src/ESPEasy.ino:500]: (warning) Member variable 'ControllerSettingsStruct::HostName' is not initialized in the constructor.
[src/ESPEasy.ino:500]: (warning) Member variable 'ControllerSettingsStruct::Publish' is not initialized in the constructor.
[src/ESPEasy.ino:500]: (warning) Member variable 'ControllerSettingsStruct::Subscribe' is not initialized in the constructor.
Fixing these cppcheck errors:
101.43s$ cppcheck --enable=warning src/*.ino -q --force -I src --include=src/ESPEasy.ino --error-exitcode=1
[src/ESPEasy.ino:500]: (warning) Member variable 'ControllerSettingsStruct::HostName' is not initialized in the constructor.
[src/ESPEasy.ino:500]: (warning) Member variable 'ControllerSettingsStruct::Publish' is not initialized in the constructor.
[src/ESPEasy.ino:500]: (warning) Member variable 'ControllerSettingsStruct::Subscribe' is not initialized in the constructor.
* [crashes] Added constructors to initialize all members in structs
Numerous structs are defined, but none of them have default constructors and there is no guarantee the members will be set when used.
With these default constructors, the parameters at least have an initialized value.
* [PubSubClient] Add bound checks on the internal buffer
Not sure if this was really causing an issue, but proper bound checks are always a good thing.
* [Crash Switch] Disabled delayBackground and added yield() calls
Something really fishy is going on with the delayBackground function, which will result in crashes when pressing the switch multiple times, with Domoticz MQTT enabled as first controller.
Disabled for now and delay(1) added to give background tasks a chance to do their work and make sure the watchdog doesn't perform a reset.
* [CI build errors] Commented out some unused variables
Travis considers them as error and fails the checks.
* [CI check] Out-of-bounds check fix
Last few days a number of issues and forum topic was about the type of flash used on the ESP boards.
This is an extension of the detailed information page.
Perhaps also merge with the newer and more clear layout of pull request #624?
That pull request was only merged to the mega branch.
I kept the changes local, but perhaps they should be placed in the "Storage" section introduced with #624.
Maybe also that pull request should get merged into the v2.0 branch.
As described in #673 .
The problem was partly related to the default values stored in flash ("0"), which was not a valid value for the switch type.
When upgrading from an older version of ESPeasy, make sure to check the switch type (normal switch or dimmer) and save the settings for the switch device again, even when nothing was changed.
Default configuration and new added switches will now work like intended.
When a controller is enabled (e.g. Domoticz MQTT or -HTTP) and the button is pressed multiple times, the ESP may reboot. See issue #674.
* [SDS011] Add send commands to sensor
In the library used to communicate to the SDS011 sensor was only support to receive data from the sensor and not query the sensor or set another mode.
This is needed for #499 , to let the sensor sleep.
N.B. code is not yet tested, only implemented while reading the datasheet "Laser Dust Sensor Control Protocol V1.3"
* [SDS011] Lessen load on ESP by polling less frequent and use SoftSerial
The default setting were to set the delay to 0 and use an own software serial implementation.
This caused frequent timeouts on the web interface, WiFi reconnects, etc.
Now the already present SoftSerial is being used. This will gather all the data from the serial port and thus there is no need to poll 50 times a second.
Now the ESP is much more responsive.
* [SDS011] Allow the sensor to sleep to extend sensor lifetime
The internal laser of the SDS011 only will last for about 1 year when ran continuously.
When the RX of the sensor is connected, it can be set to sleep for N minutes between measurements. This will extend the lifetime of the sensor and reduce power consumption.
This sleep time is stored inside the flash of the sensor, so it can be set once and then the RX on the sensor could be disconnected again to be used for other purposes.
As discussed in pull request #629 and the new issue #658 and also on https://github.com/knolleary/pubsubclient/issues/375
In short, the PubSubClient does not store the domainname used to connect to, but only a pointer to the string.
However, PubSubClient should not expect this pointer to remain valid, since it is outside its scope. So PubSubClient should keep the domainname stored in its own variables.
This fixes the problem where the MQTT broker is no longer reachable after a while when using DNS instead of IP.
* initial support for TSL2591 sensor
* return lux, visible, ir and full light separately
* better plugin init
* check sensor initialization before reading it..
* incorporated a few pending fixes for the adafruit library
* minor typo
* [mega] Detect client IP for SysInfo page and some cleanup
Added formatIP functions for readability and add client IP to SystemInfo page as preparation to detect origin just to get an idea of possibilities for #647.
Also added some reserve() statements to Strings to prevent heap fragmentation.
* [mega] Cleanup formatIP calls
* [security] #647 Add IP filtering to web interface and commands
As discussed in #647:
In the Config tab, a "Client IP filtering" section is added.
This allows for 3 levels of IP filtering:
* "Allow All" - does not imply any filtering based on IP address of the client.
* "Allow Local Subnet" - Allow only clients from within the local subnet, based on IP and subnetmask of the ESP.
* "Allow IP range" - Allow only clients within a range of IP-addresses.
Settings like these are very likely to lock out the rightful owner, so there are also two commands added, which can be sent via the serial connection.
* accessinfo
* clearaccessblock
The first one just displays the current active IP filtering.
The "clearaccessblock" command will temporarily disable the access filtering. This allows the user to login and reset the access filtering.
"Allow Local Subnet" is set as factory default.
Only when first loading a new firmware with this feature and existing configuration, the "All Allowed" is active (the old default)
* [DNS/IP] Obey UseDNS setting for all controllers
As described in #381#261 and #521
A first attempt to let all controllers use the same logic to connect to external hosts.
* [WiFi] Avoid timeouts when not connected to WiFi
As discussed in #589
Stil needed to actively disconnect network services when network was disconnected.
* [WiFi] Actively ignore network services when disconnected
All controllers now stop sending when WiFi disconnected.
Also add NTP update directly after connection was made.
Delay with waiting for unavailable network is now about 30 seconds, then normal boot continues. Every 60 seconds the WiFi will be polled again.
* [time overflow] Use separate function to compute time differences
As discussed in #594
The timeOut() function had already a remark that it was behaving fishy.
It is now split into a timeDiff function and two convenience functions:
- timeOutReached
- timePassedSince
The timeDiff function may be a bit more elaborate than strictly needed, but it is very important to do it right and the original notation was very hard to read and understand.
Almost all locations in the code where millis() was used to compute a time difference or check for timeouts now use these functions.
Potentially all of these locations could cause issues when the timer wraps.
* [time overflow] Fix for a one-off error
2^31-1 can be casted to a long value.
Thus changed "<" into "<="
* [addLib] Added SoftwareSerial library
Added latest version from: https://github.com/plerup/espsoftwareserial
* [renLib] Renamed files to avoid conflicts with existing code
* [renLib] Changed include according to rename
* [renLib] Renamed all occurences and includes and removed unused pins
Renamed to make sure all plugins use the 'new' ESPeasySoftwareSerial.
Also added pinToIndex function to reduce memory footprint with about 150 Bytes, as described in issue #630
* [unused pins] Adjust indices in object list
Forgot to change the indices in the object list of SoftwareSerial
* Simple patch for timeouts
As mentioned in this issue: https://github.com/plerup/espsoftwareserial/issues/54
* [SoftSerial] Set ObjList static
Set the object list static to share all SoftwareSerial iRAM used as described in #630
* [revertLib] Revert to old version lib, since new version uses more iram
Just to test with old version, originally available in 2.3.0 library, to see if memory usage improves.
* [test] Reduce number of ports to 1 and lower buffer size to 18 for MHZ19
Just as a test, to see what happens to the iRAM usage, lower the number of concurrent softserial ports to 1.
Also the default buffer size = 64 Bytes. The MH-Z19 sensor can do with less, since a response will be up to 9 bytes, a 18-byte buffer allows for 2 messages to be stored.
* Enable usage of up to 10 concurrent softserial and reduce variable sizes
Re-enable use of up to 10 concurrent software serials.
Also reduce the variable sizes to smaller ranges. (e.g. uint8 instead of int)
* [test] Limit number of concurrent software serial devices
Earlier tests show the amount of iRAM used is somewhat related to the maximum number of allowed software serial ports.
In this test it is set to 3 and they are assigned through first come first served a slot.
* Optimisation: save RAM.
* Another RAM optimisation (freeing RAM by moving static data from RAM to program memory).
* Fixing user-visible typos.
* Fixing typos in variables and comments.
* Fixing typos in comments.
* Revert changes of other pull request.
The system variable %ip% truncates the last octet or so when printed on small displays. Now there are four new variables %ip1%, %ip2%... so that the octet printout can be distibuted across two lines.
Possible fix for #581.
Just looking at the description of the problem, this may be causing the crashes,since the commands may be trying to dereference the LCD pointer while it still is NULL.
Cppcheck warned for 'suspicious code':
[src\_P039_Thermocouple.ino:254]: (warning) Suspicious code: sign conversion of -1 in calculation because '-1' has a negative value
I agree with cppcheck that the code is at least suspicious and probably compiler dependent.
So in order to let cppcheck no longer output a warning and make it a bit more readable, I made this change.
Also added logs to indicate errors reported by the sensor.
Possible fix for #581.
Just looking at the description of the problem, this may be causing the crashes,since the commands may be trying to dereference the LCD pointer while it still is NULL.
* [SSD1306] Upgrade library to version 3.0
The library at https://github.com/squix78/esp8266-oled-ssd1306 has to be initialized differently in version 3.0
Known issue: The font for 3 lines is not working, so temporary used the same font as for 4 ilnes. The online font generator is currently unavailable at http://oleddisplay.squix.ch/
* OLED framed improve header footer
The header now has better visible WiFi bars indicator and alternates the device name and the connected WiFi SSID.
The bottom part now only shows dots for the pages with visible data instead of the maximum number of pages possible.
* [SSD1306] Upgrade library to version 3.2.7
Forgot to commit deletion of obsolete files in previous commit.
* [SSD1306] Added 12pt font for version 3.x of the library
The font generator is online again: http://oleddisplay.squix.ch/#/home
Added Dialog Plain 12 font for the 3-line display mode.
* [OLED_Framed] Allow to use either SSD1306 or SH1106
The new OLED library allows to use SH1106 and SSD1306 controler.
Added support for both with an selector to select the available controler.
* [OLED_Framed] Only destruct and construct display object when changed
* [OLED Framed] Add contrast setting to display
Both SSD1306 and SH1106 support setting the contrast.
* Update _P036_FrameOLED.ino
* [MH-Z19] Allow for B-version and add filtering
The "B" version of the sensor does not output an S value, but does internally apply a dynamic response filter on the samples based on the amount of fluctiation in the data.
The implemented filter does something similar for the "A" version and for both adds the option for an extra delay filter to smooth the data.
Default filter setting ("off") is the old behavior, where only stable values are allowed.
* [MH-Z19] Improve label texts and logging
The first commit for the filtering had some confusing text labels.
Also it would be nice to see the effect of filtering in the logs.
Retaining will messages allows monitoring agent to receive full info about clients state.
Without retaining, the monitoring agent will only be informed about events (connect/connection lost) happening during agent's connection to broker. Any reconnect would cause monitoring agent to lose state.
* [SSD1306] Upgrade library to version 3.0
The library at https://github.com/squix78/esp8266-oled-ssd1306 has to be initialized differently in version 3.0
Known issue: The font for 3 lines is not working, so temporary used the same font as for 4 ilnes. The online font generator is currently unavailable at http://oleddisplay.squix.ch/
* OLED framed improve header footer
The header now has better visible WiFi bars indicator and alternates the device name and the connected WiFi SSID.
The bottom part now only shows dots for the pages with visible data instead of the maximum number of pages possible.
* [SSD1306] Upgrade library to version 3.2.7
Forgot to commit deletion of obsolete files in previous commit.
* [SSD1306] Added 12pt font for version 3.x of the library
The font generator is online again: http://oleddisplay.squix.ch/#/home
Added Dialog Plain 12 font for the 3-line display mode.
The header now has better visible WiFi bars indicator and alternates the device name and the connected WiFi SSID.
The bottom part now only shows dots for the pages with visible data instead of the maximum number of pages possible.
* Enhanced Dallas pooling to avoid use of delay(800)
DS_readTemp has been split in 2: DS_convertTemp and DS_readonlyTemp.
DS_convertTemp is first called after DS_setResolution.
Then DS_convertTemp is called after temp has been read.
DS_readTemp has been kept for compatibility.
The only downside is that you read the temperature of previous query (value set by Timer/TDT option).
* typo
* Moved to Environment + code cleaning
- Moved Plugin from Temperature to Environment
- Modified Plugin_004_DS_crc8 to check CRC8, not return it
- Renamed Plugin_004_DS_convertTemp to Plugin_004_DS_startConvertion and removed useless vars in it
- Removed unneed braces and empty lines
- Added comments
* Single function for format to user defined number decimals
In a number of files the same long definition was cut and paste a lot to format values to a user defined number of decimals.
Now a new simple function is added to Misc to perform this formatting, which results in more clean code, less prone to errors and a reduction in use of resources.
* Single function for format to user defined number decimals
In a number of files the same long definition was cut and paste a lot to format values to a user defined number of decimals.
Now a new simple function is added to Misc to perform this formatting, which results in more clean code, less prone to errors and a reduction in use of resources.
* P028 now supports both BME280 and BMP280
Both plugins P028 and P030 had a lot of code duplication. This takes up resources and is hard to maintain.
Now the P028 plugin can detect and use both sensors so P030 may be removed.
Only caveat is that the BMP280 does not measure humidity and thus actually is a 2-value sensor. The Domotics MQTT controller did not distinguish between them, but other controllers may do so.
When needed, the P030 plugin can still be a mere stub for the output and plugin definition and still share all code with P028.
* [BME280] Add temperature offset and improve read stability
The BME280/BMP280 may heat up internally if read too often and too long.
Also when built in a small container along with other sensors and the ESP, the sensor may read values which are too high.
To compensate for these higher readings, a constant offset may be applied in the device parameters.
This value is a signed integer value representing the offset in 1/10th degree Celsius.
Since the humidity is a relative value, depending on the temperature, this should be adjusted also.
Only this computed dew point temperature is also too high, due to the fact the sensor is warmer than the air and thus the perceived humidity is off.
To correct for this, half the offset temperature is being used to compute the dew point temperature.
The other improvement is the routine to read the sensor.
Using this routine, the sensor is only active for about 1.6 seconds each minute.
This prevents the sensor to heat up from its own readings and also allows stable readings using some filtering. (slamming a door does not affect the readings)
* [BMx280] Auto detect connected chip ID and show in Device config tab
Detect connected chip (BME280/BMP280) automatically and show detected device immediately in the Device config page next to the I2C address selection.
* [BME/BMP280] Perform reset at init
Just to make the reading a bit more stable when the sensor stops responding.
This is also done in the "official" Bosch github: https://github.com/BoschSensortec/BME280_driver
* [BMx280] Allow for more than one sensor
As suggested in #491 for another sensor, its I2Caddress was handled incorrectly. The same applied to this plugin.
As described in #491.
The calibration settings are now stored per instance and the I2C address is now taken from the taskvalue array and no longer a global variable.
%eventvalue% parsing didn't correctly process literal strings (that
start with '!'). It tried to extract the value from the righthand of
'=', where it should parse the entire string.
Introduction and wiki: https://www.letscontrolit.com/wiki/index.php/ESPEasy#Introduction
This is the development branch for the next upcoming release (2.0.0). This is also known as ESPEasyMega.
**MEGA**
:warning:This is the development branch of ESPEasy. All new untested features go into this branch. If you want to do a bugfix, do it on the stable branch, we will merge the fix to the development branch as well.:warning:
Next stable branch: https://github.com/letscontrolit/ESPEasy/tree/v2.0 (bug fixes only, since oct 2017))
Check here to learn how to use this branch and help us improving ESPEasy: http://www.letscontrolit.com/wiki/index.php/ESPEasy#Source_code_development
## Versions
* v2.0.0-devX: these are the current development releases. use these if you want bleeding edge features, or if you want to help us testing and developing. new release every month.
* v2.0.0-betaX: as soon as we think its stable/complete enough for real testing, we will start numbering beta's.
// hoher Bereich, 1 lx Modus, normale Empfindlichkeit. Der Wert von 60000 ist mehr oder weniger zufällig, es mus einfach ein hoher Wert, nah an der Grenze sein.
#define SENSORS_MAGFIELD_EARTH_MAX (60.0F) /**< Maximum magnetic field on Earth's surface */
#define SENSORS_MAGFIELD_EARTH_MIN (30.0F) /**< Minimum magnetic field on Earth's surface */
#define SENSORS_PRESSURE_SEALEVELHPA (1013.25F) /**< Average sea level pressure is 1013.25 hPa */
#define SENSORS_DPS_TO_RADS (0.017453293F) /**< Degrees/s to rad/s multiplier */
#define SENSORS_GAUSS_TO_MICROTESLA (100) /**< Gauss to micro-Tesla multiplier */
/** Sensor types */
typedefenum
{
SENSOR_TYPE_ACCELEROMETER=(1),/**< Gravity + linear acceleration */
SENSOR_TYPE_MAGNETIC_FIELD=(2),
SENSOR_TYPE_ORIENTATION=(3),
SENSOR_TYPE_GYROSCOPE=(4),
SENSOR_TYPE_LIGHT=(5),
SENSOR_TYPE_PRESSURE=(6),
SENSOR_TYPE_PROXIMITY=(8),
SENSOR_TYPE_GRAVITY=(9),
SENSOR_TYPE_LINEAR_ACCELERATION=(10),/**< Acceleration not including gravity */
SENSOR_TYPE_ROTATION_VECTOR=(11),
SENSOR_TYPE_RELATIVE_HUMIDITY=(12),
SENSOR_TYPE_AMBIENT_TEMPERATURE=(13),
SENSOR_TYPE_VOLTAGE=(15),
SENSOR_TYPE_CURRENT=(16),
SENSOR_TYPE_COLOR=(17)
}sensors_type_t;
/** struct sensors_vec_s is used to return a vector in a common format. */
typedefstruct{
union{
floatv[3];
struct{
floatx;
floaty;
floatz;
};
/* Orientation sensors */
struct{
floatroll;/**< Rotation around the longitudinal axis (the plane body, 'X axis'). Roll is positive and increasing when moving downward. -90°<=roll<=90° */
floatpitch;/**< Rotation around the lateral axis (the wing span, 'Y axis'). Pitch is positive and increasing when moving upwards. -180°<=pitch<=180°) */
floatheading;/**< Angle between the longitudinal axis (the plane body) and magnetic north, measured clockwise when viewing from the top of the device. 0-359° */
};
};
int8_tstatus;
uint8_treserved[3];
}sensors_vec_t;
/** struct sensors_color_s is used to return color data in a common format. */
typedefstruct{
union{
floatc[3];
/* RGB color space */
struct{
floatr;/**< Red component */
floatg;/**< Green component */
floatb;/**< Blue component */
};
};
uint32_trgba;/**< 24-bit RGBA value */
}sensors_color_t;
/* Sensor event (36 bytes) */
/** struct sensor_event_s is used to provide a single sensor event in a common format. */
typedefstruct
{
int32_tversion;/**< must be sizeof(struct sensors_event_t) */
int32_tsensor_id;/**< unique sensor identifier */
int32_ttype;/**< sensor type */
int32_treserved0;/**< reserved */
int32_ttimestamp;/**< time is in milliseconds */
union
{
floatdata[4];
sensors_vec_tacceleration;/**< acceleration values are in meter per second per second (m/s^2) */
sensors_vec_tmagnetic;/**< magnetic vector values are in micro-Tesla (uT) */
sensors_vec_torientation;/**< orientation values are in degrees */
sensors_vec_tgyro;/**< gyroscope values are in rad/s */
floattemperature;/**< temperature is in degrees centigrade (Celsius) */
floatdistance;/**< distance in centimeters */
floatlight;/**< light in SI lux units */
floatpressure;/**< pressure in hectopascal (hPa) */
floatrelative_humidity;/**< relative humidity in percent */
floatcurrent;/**< current in milliamps (mA) */
floatvoltage;/**< voltage in volts (V) */
sensors_color_tcolor;/**< color in RGB component values */
};
}sensors_event_t;
/* Sensor details (40 bytes) */
/** struct sensor_s is used to describe basic information about a specific sensor. */
typedefstruct
{
charname[12];/**< sensor name */
int32_tversion;/**< version of the hardware + driver */
int32_tsensor_id;/**< unique sensor identifier */
int32_ttype;/**< this sensor's type (ex. SENSOR_TYPE_LIGHT) */
floatmax_value;/**< maximum value of this sensor's value in SI units */
floatmin_value;/**< minimum value of this sensor's value in SI units */
floatresolution;/**< smallest difference between two values reported by this sensor */
int32_tmin_delay;/**< min delay in microseconds between events. zero = not a constant rate */
Many small embedded systems exist to collect data from sensors, analyse the data, and either take an appropriate action or send that sensor data to another system for processing.
One of the many challenges of embedded systems design is the fact that parts you used today may be out of production tomorrow, or system requirements may change and you may need to choose a different sensor down the road.
Creating new drivers is a relatively easy task, but integrating them into existing systems is both error prone and time consuming since sensors rarely use the exact same units of measurement.
By reducing all data to a single **sensors\_event\_t** 'type' and settling on specific, **standardised SI units** for each sensor family the same sensor types return values that are comparable with any other similar sensor. This enables you to switch sensor models with very little impact on the rest of the system, which can help mitigate some of the risks and problems of sensor availability and code reuse.
The unified sensor abstraction layer is also useful for data-logging and data-transmission since you only have one well-known type to log or transmit over the air or wire.
## Unified Sensor Drivers ##
The following drivers are based on the Adafruit Unified Sensor Driver:
Any driver that supports the Adafruit unified sensor abstraction layer will implement the Adafruit\_Sensor base class. There are two main typedefs and one enum defined in Adafruit_Sensor.h that are used to 'abstract' away the sensor details and values:
**Sensor Types (sensors\_type\_t)**
These pre-defined sensor types are used to properly handle the two related typedefs below, and allows us determine what types of units the sensor uses, etc.
```
/** Sensor types */
typedef enum
{
SENSOR_TYPE_ACCELEROMETER = (1),
SENSOR_TYPE_MAGNETIC_FIELD = (2),
SENSOR_TYPE_ORIENTATION = (3),
SENSOR_TYPE_GYROSCOPE = (4),
SENSOR_TYPE_LIGHT = (5),
SENSOR_TYPE_PRESSURE = (6),
SENSOR_TYPE_PROXIMITY = (8),
SENSOR_TYPE_GRAVITY = (9),
SENSOR_TYPE_LINEAR_ACCELERATION = (10),
SENSOR_TYPE_ROTATION_VECTOR = (11),
SENSOR_TYPE_RELATIVE_HUMIDITY = (12),
SENSOR_TYPE_AMBIENT_TEMPERATURE = (13),
SENSOR_TYPE_VOLTAGE = (15),
SENSOR_TYPE_CURRENT = (16),
SENSOR_TYPE_COLOR = (17)
} sensors_type_t;
```
**Sensor Details (sensor\_t)**
This typedef describes the specific capabilities of this sensor, and allows us to know what sensor we are using beneath the abstraction layer.
```
/* Sensor details (40 bytes) */
/** struct sensor_s is used to describe basic information about a specific sensor. */
typedef struct
{
char name[12];
int32_t version;
int32_t sensor_id;
int32_t type;
float max_value;
float min_value;
float resolution;
int32_t min_delay;
} sensor_t;
```
The individual fields are intended to be used as follows:
- **name**: The sensor name or ID, up to a maximum of twelve characters (ex. "MPL115A2")
- **version**: The version of the sensor HW and the driver to allow us to differentiate versions of the board or driver
- **sensor\_id**: A unique sensor identifier that is used to differentiate this specific sensor instance from any others that are present on the system or in the sensor network
- **type**: The sensor type, based on **sensors\_type\_t** in sensors.h
- **max\_value**: The maximum value that this sensor can return (in the appropriate SI unit)
- **min\_value**: The minimum value that this sensor can return (in the appropriate SI unit)
- **resolution**: The smallest difference between two values that this sensor can report (in the appropriate SI unit)
- **min\_delay**: The minimum delay in microseconds between two sensor events, or '0' if there is no constant sensor rate
**Sensor Data/Events (sensors\_event\_t)**
This typedef is used to return sensor data from any sensor supported by the abstraction layer, using standard SI units and scales.
```
/* Sensor event (36 bytes) */
/** struct sensor_event_s is used to provide a single sensor event in a common format. */
typedef struct
{
int32_t version;
int32_t sensor_id;
int32_t type;
int32_t reserved0;
int32_t timestamp;
union
{
float data[4];
sensors_vec_t acceleration;
sensors_vec_t magnetic;
sensors_vec_t orientation;
sensors_vec_t gyro;
float temperature;
float distance;
float light;
float pressure;
float relative_humidity;
float current;
float voltage;
sensors_color_t color;
};
} sensors_event_t;
```
It includes the following fields:
- **version**: Contain 'sizeof(sensors\_event\_t)' to identify which version of the API we're using in case this changes in the future
- **sensor\_id**: A unique sensor identifier that is used to differentiate this specific sensor instance from any others that are present on the system or in the sensor network (must match the sensor\_id value in the corresponding sensor\_t enum above!)
- **type**: the sensor type, based on **sensors\_type\_t** in sensors.h
- **timestamp**: time in milliseconds when the sensor value was read
- **data[4]**: An array of four 32-bit values that allows us to encapsulate any type of sensor data via a simple union (further described below)
**Required Functions**
In addition to the two standard types and the sensor type enum, all drivers based on Adafruit_Sensor must also implement the following two functions:
```
bool getEvent(sensors_event_t*);
```
Calling this function will populate the supplied sensors\_event\_t reference with the latest available sensor data. You should call this function as often as you want to update your data.
```
void getSensor(sensor_t*);
```
Calling this function will provide some basic information about the sensor (the sensor name, driver version, min and max values, etc.
**Standardised SI values for sensors\_event\_t**
A key part of the abstraction layer is the standardisation of values on SI units of a particular scale, which is accomplished via the data[4] union in sensors\_event\_t above. This 16 byte union includes fields for each main sensor type, and uses the following SI units and scales:
- **acceleration**: values are in **meter per second per second** (m/s^2)
- **magnetic**: values are in **micro-Tesla** (uT)
- **orientation**: values are in **degrees**
- **gyro**: values are in **rad/s**
- **temperature**: values in **degrees centigrade** (Celsius)
- **distance**: values are in **centimeters**
- **light**: values are in **SI lux** units
- **pressure**: values are in **hectopascal** (hPa)
- **relative\_humidity**: values are in **percent**
- **current**: values are in **milliamps** (mA)
- **voltage**: values are in **volts** (V)
- **color**: values are in 0..1.0 RGB channel luminosity and 32-bit RGBA format
## The Unified Driver Abstraction Layer in Practice ##
Using the unified sensor abstraction layer is relatively easy once a compliant driver has been created.
Every compliant sensor can now be read using a single, well-known 'type' (sensors\_event\_t), and there is a standardised way of interrogating a sensor about its specific capabilities (via sensor\_t).
An example of reading the [TSL2561](https://github.com/adafruit/Adafruit_TSL2561) light sensor can be seen below:
Thank you for opening an issue on an Adafruit Arduino library repository. To
improve the speed of resolution please review the following guidelines and
common troubleshooting steps below before creating the issue:
- **Do not use GitHub issues for troubleshooting projects and issues.** Instead use
the forums at http://forums.adafruit.com to ask questions and troubleshoot why
something isn't working as expected. In many cases the problem is a common issue
that you will more quickly receive help from the forum community. GitHub issues
are meant for known defects in the code. If you don't know if there is a defect
in the code then start with troubleshooting on the forum first.
- **If following a tutorial or guide be sure you didn't miss a step.** Carefully
check all of the steps and commands to run have been followed. Consult the
forum if you're unsure or have questions about steps in a guide/tutorial.
- **For Arduino projects check these very common issues to ensure they don't apply**:
- For uploading sketches or communicating with the board make sure you're using
a **USB data cable** and **not** a **USB charge-only cable**. It is sometimes
very hard to tell the difference between a data and charge cable! Try using the
cable with other devices or swapping to another cable to confirm it is not
the problem.
- **Be sure you are supplying adequate power to the board.** Check the specs of
your board and plug in an external power supply. In many cases just
plugging a board into your computer is not enough to power it and other
peripherals.
- **Double check all soldering joints and connections.** Flakey connections
cause many mysterious problems. See the [guide to excellent soldering](https://learn.adafruit.com/adafruit-guide-excellent-soldering/tools) for examples of good solder joints.
- **Ensure you are using an official Arduino or Adafruit board.** We can't
guarantee a clone board will have the same functionality and work as expected
with this code and don't support them.
If you're sure this issue is a defect in the code and checked the steps above
please fill in the following fields to provide enough troubleshooting information.
You may delete the guideline and text above to just leave the following details:
#define TSL2591_COMMAND_BIT (0xA0) // 1010 0000: bits 7 and 5 for 'command normal'
#define TSL2591_CLEAR_INT (0xE7)
#define TSL2591_TEST_INT (0xE4)
#define TSL2591_WORD_BIT (0x20) // 1 = read/write word (rather than byte)
#define TSL2591_BLOCK_BIT (0x10) // 1 = using block read/write
#define TSL2591_ENABLE_POWEROFF (0x00)
#define TSL2591_ENABLE_POWERON (0x01)
#define TSL2591_ENABLE_AEN (0x02) // ALS Enable. This field activates ALS function. Writing a one activates the ALS. Writing a zero disables the ALS.
#define TSL2591_ENABLE_AIEN (0x10) // ALS Interrupt Enable. When asserted permits ALS interrupts to be generated, subject to the persist filter.
#define TSL2591_ENABLE_NPIEN (0x80) // No Persist Interrupt Enable. When asserted NP Threshold conditions will generate an interrupt, bypassing the persist filter
This is an Arduino library for the TSL2591 digital luminosity (light) sensors.
Pick one up at http://www.adafruit.com/products/1980
To download. click the DOWNLOADS button in the top right corner, rename the uncompressed folder Adafruit_TSL2591. Check that the Adafruit_TSL2591 folder contains Adafruit_TSL2591.cpp and Adafruit_TSL2591.h
Place the Adafruit_TSL2591 library folder your <arduinosketchfolder>/libraries/ folder. You may need to create the libraries subfolder if its your first library. Restart the IDE.
You'll also need the Adafruit_Sensor library from https://github.com/adafruit/Adafruit_Sensor
* Made sure we don't read more that necessary (issue #422)
* Fixed error when the key of a `JsonObject` is a `char[]` (issue #423)
* Reduced code size when using `const` references
* Fixed error with string of type `unsigned char*` (issue #428)
* Added `deprecated` attribute on `asArray()`, `asObject()` and `asString()` (issue #420)
v5.8.1
------
* Fixed error when assigning a `volatile int` to a `JsonVariant` (issue #415)
* Fixed errors with Variable Length Arrays (issue #416)
* Fixed error when both `ARDUINOJSON_ENABLE_STD_STREAM` and `ARDUINOJSON_ENABLE_ARDUINO_STREAM` are set to `1`
* Fixed error "Stream does not name a type" (issue #412)
v5.8.0
------
* Added operator `==` to compare `JsonVariant` and strings (issue #402)
* Added support for `Stream` (issue #300)
* Reduced memory consumption by not duplicating spaces and comments
> ### BREAKING CHANGES :warning:
>
> `JsonBuffer::parseObject()` and `JsonBuffer::parseArray()` have been pulled down to the derived classes `DynamicJsonBuffer` and `StaticJsonBufferBase`.
>
> This means that if you have code like:
>
> ```c++
> void myFunction(JsonBuffer& jsonBuffer);
> ```
>
> you need to replace it with one of the following:
* Added an `printTo(char[N])` and `prettyPrintTo(char[N])` (issue #292)
* Added ability to set a nested value like this: `root["A"]["B"] = "C"` (issue #352)
* Renamed `*.ipp` to `*Impl.hpp` because they were ignored by Arduino IDE (issue #396)
v5.7.2
------
* Made PROGMEM available on more platforms (issue #381)
* Fixed PROGMEM causing an exception on ESP8266 (issue #383)
v5.7.1
------
* Added support for PROGMEM (issue #76)
* Fixed compilation error when index is not an `int` (issue #381)
v5.7.0
------
* Templatized all functions using `String` or `std::string`
* Removed `ArduinoJson::String`
* Removed `JsonVariant::defaultValue<T>()`
* Removed non-template `JsonObject::get()` and `JsonArray.get()`
* Fixed support for `StringSumHelper` (issue #184)
* Replaced `ARDUINOJSON_USE_ARDUINO_STRING` by `ARDUINOJSON_ENABLE_STD_STRING` and `ARDUINOJSON_ENABLE_ARDUINO_STRING` (issue #378)
* Added example `StringExample.ino` to show where `String` can be used
* Increased default nesting limit to 50 when compiled for a computer (issue #349)
> ### BREAKING CHANGES :warning:
>
> The non-template functions `JsonObject::get()` and `JsonArray.get()` have been removed. This means that you need to explicitely tell the type you expect in return.
* Fixed `array[idx].as<JsonVariant>()` and `object[key].as<JsonVariant>()`
* Fixed return value of `JsonObject::set()` (issue #350)
* Fixed undefined behavior in `Prettyfier` and `Print` (issue #354)
* Fixed parser that incorrectly rejected floats containing a `+` (issue #349)
v5.6.6
------
* Fixed `-Wparentheses` warning introduced in v5.6.5 (PR #335 by @nuket)
* Added `.mbedignore` for ARM mbdeb (PR #334 by @nuket)
* Fixed `JsonVariant::success()` which didn't propagate `JsonArray::success()` nor `JsonObject::success()` (issue #342).
v5.6.5
------
*`as<char*>()` now returns `true` when input is `null` (issue #330)
v5.6.4
------
@@ -71,8 +335,9 @@ v5.1.0
* Added support of `long long` (issue #171)
* Moved all build settings to `ArduinoJson/Configuration.hpp`
**BREAKING CHANGE**:
If you defined `ARDUINOJSON_ENABLE_STD_STREAM`, you now need to define it to `1`.
> ### BREAKING CHANGE :warning:
>
> If you defined `ARDUINOJSON_ENABLE_STD_STREAM`, you now need to define it to `1`.
v5.0.8
------
@@ -86,9 +351,10 @@ v5.0.7
* Made library easier to use from a CMake project: simply `add_subdirectory(ArduinoJson/src)`
* Changed `String` to be a `typedef` of `std::string` (issues #142 and #161)
**BREAKING CHANGES**:
-`JsonVariant(true).as<String>()` now returns `"true"` instead of `"1"`
-`JsonVariant(false).as<String>()` now returns `"false"` instead of `"0"`
> ### BREAKING CHANGES :warning:
>
> - `JsonVariant(true).as<String>()` now returns `"true"` instead of `"1"`
> - `JsonVariant(false).as<String>()` now returns `"false"` instead of `"0"`
v5.0.6
------
@@ -142,10 +408,11 @@ v5.0.0
* Redesigned `JsonVariant` to leverage converting constructors instead of assignment operators (issue #66)
* Switched to new the library layout (requires Arduino 1.0.6 or above)
**BREAKING CHANGES**:
-`JsonObject::add()` was renamed to `set()`
-`JsonArray::at()` and `JsonObject::at()` were renamed to `get()`
- Number of digits of floating point value are now set with `double_with_n_digits()`
> ### BREAKING CHANGES :warning:
>
> - `JsonObject::add()` was renamed to `set()`
> - `JsonArray::at()` and `JsonObject::at()` were renamed to `get()`
> - Number of digits of floating point value are now set with `double_with_n_digits()`
**Personal note about the `String` class**:
Support of the `String` class has been added to the library because many people use it in their programs.
@@ -198,106 +465,7 @@ v4.0
* Unified parser and generator API (issue #23)
* Updated library layout, now requires Arduino 1.0.6 or newer
**BREAKING CHANGE**: API changed significantly, see [Migrating code to the new API](https://github.com/bblanchon/ArduinoJson/wiki/Migrating-code-to-the-new-API).
> ### BREAKING CHANGES :warning:
>
> API changed significantly since v3, see [Migrating code to the new API](https://arduinojson.org/doc/migration/).
v3.4
----
* Fixed escaped char parsing (issue #16)
v3.3
----
* Added indented output for the JSON generator (issue #11), see example bellow.
* Added `IndentedPrint`, a decorator for `Print` to allow indented output
Example:
JsonOject<2> json;
json["key"] = "value";
json.prettyPrintTo(Serial);
v3.2
----
* Fixed a bug when adding nested object in `JsonArray` (bug introduced in v3.1).
v3.1
----
* Calling `Generator::JsonObject::add()` twice with the same `key` now replaces the `value`
* Added `Generator::JsonObject::operator[]`, see bellow the new API
Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the “Software”), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:
See the [tutorial on arduinojson.org](https://arduinojson.org/doc/encoding/?utm_source=github&utm_medium=readme)
Documentation
-------------
## Documentation
The documentation is available online in the [Arduino JSON wiki](https://github.com/bblanchon/ArduinoJson/wiki)
The documentation is available on [arduinojson.org](https://arduinojson.org/?utm_source=github&utm_medium=readme), here are some shortcuts:
Testimonials
------------
From Arduino's Forum user `jflaplante`:
> I tried aJson json-arduino before trying your library. I always ran into memory problem after a while.
> I have no such problem so far with your library. It is working perfectly with my web services.
From Arduino's Forum user `gbathree`:
> Thanks so much - this is an awesome library! If you want to see what we're doing with it - the project is located at www.photosynq.org.
From StackOverflow user `thegreendroid`:
> It has a really elegant, simple API and it works like a charm on embedded and Windows/Linux platforms. We recently started using this on an embedded project and I can vouch for its quality.
From GitHub user `zacsketches`:
> Thanks for a great library!!!
> I've been watching you consistently develop this library over the past six months, and I used it today for a publish and subscribe architecture designed to help hobbyists move into more advanced robotics. Your library allowed me to implement remote subscription in order to facilitate multi-processor robots.
> ArduinoJson saved me a week's worth of time!!
[From Reddit user `erm_what_`](https://www.reddit.com/r/arduino/comments/3jj6ep/announcing_arduinojson_50/cusjk8c):
> This is a great library and I wouldn't be able to do the project I'm doing without it. I completely recommend it.
[From Reddit user `makerhacks`](https://www.reddit.com/r/arduino/comments/3jj6ep/announcing_arduinojson_50/cusqg7b):
> I am just starting an ESP8266 clock project and now I can output JSON from my server script and interpret it painlessly.
[From Twitter user `@hemalchevli`](https://twitter.com/hemalchevli/status/715788439397011456):
> ArduinoJson library should be used as a benchmark/reference for making libraries. Truly elegant.
Donators
--------
Special thanks to the following persons and companies who made generous donations to the library author:
* Robert Murphy <img alt='USA' src='https://cdnjs.cloudflare.com/ajax/libs/emojione/2.1.4/assets/svg/1f1fa-1f1f8.svg' width='18' height='18'>
* Martijn van den Burg <img alt='Netherlands' src='https://cdnjs.cloudflare.com/ajax/libs/emojione/2.1.4/assets/svg/1f1f3-1f1f1.svg' width='18' height='18'>
* Nick Koumaris <img alt='Greece' src='https://cdnjs.cloudflare.com/ajax/libs/emojione/2.1.4/assets/svg/1f1ec-1f1f7.svg' width='18' height='18'>
* Jon Williams <img alt='USA' src='https://cdnjs.cloudflare.com/ajax/libs/emojione/2.1.4/assets/svg/1f1fa-1f1f8.svg' width='18' height='18'>
* The [Examples](https://arduinojson.org/example/?utm_source=github&utm_medium=readme) show how to use the library in various situations.
* The [API Reference](https://arduinojson.org/api/?utm_source=github&utm_medium=readme) contains the description of each class and function.
* The [FAQ](https://arduinojson.org/faq/?utm_source=github&utm_medium=readme) has the answer to virtually every question.
* The [ArduinoJson Assistant](https://arduinojson.org/assistant/?utm_source=github&utm_medium=readme) writes programs for you!
---
Found this library useful? Please star this project or [help me back with a donation!](https://www.paypal.com/cgi-bin/webscr?cmd=_donations&business=donate%40benoitblanchon%2efr&lc=GB&item_name=Benoit%20Blanchon&item_number=Arduino%20JSON¤cy_code=EUR&bn=PP%2dDonationsBF%3abtn_donate_LG%2egif%3aNonHosted) :smile:
Do you like this library? Please [star this project on GitHub](https://github.com/bblanchon/ArduinoJson/stargazers)!
What? You don't like it but you *love* it?
We don't take donations anymore, but [we sell a book](https://arduinojson.org/book/?utm_source=github&utm_medium=readme), so you can help and learn at the same time!
// A meta-function that returns true if T is a reference
template<typenameT>
structIsReference{
staticconstboolvalue=false;
};
template<typenameT>
structIsReference<T&>{
staticconstboolvalue=true;
};
}
}
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
ESPEasy release bot
GrovkillenandGitHub
Gijs NoorlanderandGitHub
Bartłomiej ZimońandGitHub
Tempura San
Saverio Cisternino
Steffen Lange
stefan
Daniel Tedenljung
Daniel TedenljungandGitHub
Plebs
ZericE
flexitiandGitHub
mvdbro
sentinel073
Hans-Rune Bue
Susis Strolch
Nuno Sousa
GeraldandGitHub
Holli
moi
s0170071
clumsy-stefanandGitHub
linuxnico
Bartlomiej ZimonandTD-er
Brian Setz
es-kaandUnknown
Panayotis Kouvarakis
JK
sassod
kahvmandGitHub
s0170071andUnknown
Michael SchröderandDatuX
Stanislav MihicandDatuX
Henri de JongandDatuX
AndreyandDatuX
wdonkerandDatuX
josemariaaraujoandDatuX
jctualandDatuX
papperoneandDatuX
chunter1andDatuX
paulv888andDatuX
krikkandDatuX
M0ebiu5andDatuX
DaMandDatuX
fensoftandDatuX
Sen HaerensandDatuX
tedenda
sakinitandDatuX
Tomasz TorczandDatuX
MichaelandDatuX
BadWolf42andDatuX
SightofSilenceandDatuX
SloMustiandDatuX
denisfrenchandDatuX
hatzlhofferandDatuX
NeoandDatuX
Alexander Schulz
