ESPEasy/lib/SparkFun SCD4x Arduino Library/examples/Example6_SignalCompensation/Example6_SignalCompensation.ino

/*
  Signal Compensation
  By: Paul Clark
  Based on earlier code by: Nathan Seidle
  SparkFun Electronics
  Date: June 3rd, 2021
  License: MIT. See license file for more information but you can
  basically do whatever you want with this code.

  Feel like supporting open source hardware?
  Buy a board from SparkFun! https://www.sparkfun.com/products/18365

  This example prints the current CO2 level, relative humidity, and temperature in C.

  Hardware Connections:
  Attach RedBoard to computer using a USB cable.
  Connect SCD40/41 to RedBoard using Qwiic cable.
  Open Serial Monitor at 115200 baud.
*/

#include <Wire.h>

#include "SparkFun_SCD4x_Arduino_Library.h" //Click here to get the library: http://librarymanager/All#SparkFun_SCD4x
SCD4x mySensor;

void setup()
{
  Serial.begin(115200);
  Serial.println(F("SCD4x Example"));
  Wire.begin();

  //mySensor.enableDebugging(); // Uncomment this line to get helpful debug messages on Serial

  if (mySensor.begin() == false)
  {
    Serial.println(F("Sensor not detected. Please check wiring. Freezing..."));
    while (1)
      ;
  }

  //We need to stop periodic measurements before we can change the sensor signal compensation settings
  if (mySensor.stopPeriodicMeasurement() == true)
  {
    Serial.println(F("Periodic measurement is disabled!"));
  }  

  //Now we can change the sensor settings.
  //There are three signal compensation commands we can use: setTemperatureOffset; setSensorAltitude; and setAmbientPressure

  Serial.print(F("Temperature offset is currently: "));
  Serial.println(mySensor.getTemperatureOffset(), 2); // Print the temperature offset with two decimal places
  mySensor.setTemperatureOffset(5); // Set the temperature offset to 5C
  Serial.print(F("Temperature offset is now: "));
  Serial.println(mySensor.getTemperatureOffset(), 2); // Print the temperature offset with two decimal places

  Serial.print(F("Sensor altitude is currently: "));
  Serial.println(mySensor.getSensorAltitude()); // Print the sensor altitude
  mySensor.setSensorAltitude(1000); // Set the sensor altitude to 1000m
  Serial.print(F("Sensor altitude is now: "));
  Serial.println(mySensor.getSensorAltitude()); // Print the sensor altitude

  //There is no getAmbientPressure command
  bool success = mySensor.setAmbientPressure(98700); // Set the ambient pressure to 98700 Pascals
  if (success)
  {
    Serial.println(F("setAmbientPressure was successful"));
  }

  //The signal compensation settings are stored in RAM by default and will reset if reInit is called
  //or if the power is cycled. To store the settings in EEPROM we can call:
  mySensor.persistSettings(); // Uncomment this line to store the sensor settings in EEPROM

  //Just for giggles, while the periodic measurements are stopped, let's read the sensor serial number
  char serialNumber[13]; // The serial number is 48-bits. We need 12 bytes plus one extra to store it as ASCII Hex
  if (mySensor.getSerialNumber(serialNumber) == true)
  {
    Serial.print(F("The sensor's serial number is: 0x"));
    Serial.println(serialNumber);
  }

  //Finally, we need to restart periodic measurements
  if (mySensor.startPeriodicMeasurement() == true)
  {
    Serial.println(F("Periodic measurements restarted!"));
  }
}

void loop()
{
  if (mySensor.readMeasurement()) // readMeasurement will return true when fresh data is available
  {
    Serial.println();

    Serial.print(F("CO2(ppm):"));
    Serial.print(mySensor.getCO2());

    Serial.print(F("\tTemperature(C):"));
    Serial.print(mySensor.getTemperature(), 1);

    Serial.print(F("\tHumidity(%RH):"));
    Serial.print(mySensor.getHumidity(), 1);

    Serial.println();
  }
  else
    Serial.print(F("."));

  delay(500);
}